2022 - 2023
Florida Department of Education
Curriculum Framework 

Program Title:	Marine Technology
Career Cluster:	Transportation, Distribution and Logistics

CCC	
CIP Number	0647060512	
Program Type	College Credit Certificate (CCC)	
Standard Length	34 credit hours	
CTSO	SkillsUSA	
SOC Codes (all applicable) 	49-3051 – Motorboat Mechanics and Service Technicians	
CTE Program Resources 	http://www.fldoe.org/academics/career-adult-edu/career-tech-edu/program-resources.stml	

Purpose

This certificate program is part of the Marine Engineering, Management & Seamanship AAS degree program (0647060500).  

A College Credit Certificate consists of a program of instruction of less than sixty (60) credits of college-level courses, which is part of an AS or AAS degree program and prepares students for entry into employment (Rule 6A-14.030, F.A.C.).

This program offers a sequence of courses that provides coherent and rigorous content aligned with challenging academic standards and relevant technical knowledge and skills needed to prepare for further education and careers in the Transportation, Distribution and Logistics career cluster; provides technical skill proficiency, and includes competency-based applied learning that contributes to the academic knowledge, higher-order reasoning and problem-solving skills, work attitudes, general employability skills, technical skills, and occupation-specific skills, and knowledge of all aspects of the Transportation, Distribution and Logistics career cluster. 

The content includes but is not limited to installation and operation of diesel and gasoline engines; troubleshooting for diesel and gasoline engines; engine maintenance; propeller selection; and corrosion control.

Additional Information relevant to this Career and Technical Education (CTE) program is provided at the end of this document.

Standards

After successfully completing this program, the student will be able to perform the following:

01.0	Perform basic shop practices.
02.0	Describe operational theory of (2) two and (4) four cycle engines - Diesel and Gasoline.
03.0	Use service manuals and parts references.
04.0	Perform basic welding skills.
05.0	Remove and install engines.
06.0	Recondition and service engines.
07.0	Perform diagnosis service and repairs to all types of marine ignition systems.
08.0	Develop skills in electrical-electronic theory of operation and application.
09.0	Troubleshoot and repair fuel systems.
10.0	Service cooling systems.
11.0	Service exhaust systems.
12.0	Repair drive systems.
13.0	Rig boats.
14.0	Repair lower units.
15.0	Perform corrosion experiments and understand corrosion control.

2022 - 2023
Florida Department of Education
Student Performance Standards

Program Title:	Marine Technology
CIP Number:	0647060512
Program Length:	34 credit hours
SOC Code(s):		49-3051

This certificate program is part of the Marine Engineering, Management & Seamanship AAS degree program (0647060500).  At the completion of this program, the student will be able to:	
01.0	Perform basic shop practices.--The student will be able to:	
01.01	Perform calculations with square roots and percentage.	
01.02	Change fractions to decimals and decimals to fractions.	
01.03	Determine metric system measurements.	
01.04	Comply with safety rules and regulations.	
01.05	Operate hand tools safely and properly.	
01.06	Set up and use power tools safely and properly.	
01.07	Set up and use precision measuring tools.	
01.08	Drill and remove broken studs and install helicoils.	
01.09	Identify threaded fasteners by size, type, thread series, thread classes, material hardness and compatibility.	
01.10	Install fasteners such as screws, bolts and keys; and utilize screw extractor, thread cutting tape and dies.	
01.11	Identify engine specifications and recommended propeller selection based on manufacture’s engine data.	
01.12	Demonstrate the ability to analyze and solve mechanical problems.	
02.0	Describe operational theory of (2) two and (4) four cycle engines diesel and gasoline.--The student will be able to:	
02.01	Distinguish between the characteristics and principles of two and four cycle engines including diesel.	
02.02	Identify the principal engine systems such as: Fuel, Cooling, Lubrication, Air Intake, and Electrical.	
02.03	Identify basic engine parts.	
02.04	Describe the functions of the crankshaft, camshaft, pistons, connecting rods, engine block, head valves, and accessories.	
02.05	List the information which may be found on the engine nameplate.	
02.06	Describe types of motion and simple machines and characteristics of energy.	
02.07	Describe the main theoretical concept of heat engines.	
02.08	Describe the process by which an internal combustion engine converts chemical energy into rotary motion.	
02.09	Calculate problems using the formulas for engine cubic displacement and compression ratio.	
02.10	Identify the parts of a camshaft lobe-crankshaft lobe.	
02.11	Describe valve timing and overlap procedures.	
02.12	Identify types of valve arrangements.	
02.13	Identify types of engine construction.	
02.14	Describe piston engine operation, design loop charged.	
02.15	Describe the operation of two and four stroke engines including diesel engines.	
02.16	Identify major engine manufacturers in today’s market.	
02.17	Describe the procedure to convert a boat with gasoline engines into a boat with diesel engines.	
03.0	Use service manuals and parts references.--The student will be able to:	
03.01	Demonstrate use of multiple and single type shop service manual.	
03.02	Demonstrate use of specification handbooks and maintenance charts.	
03.03	Demonstrate use of manufacturer parts catalogs.	
03.04	Demonstrate use of marine engine installation manuals.	
03.05	Demonstrate use of manufacture’s service bulletins.	
03.06	Apply processes to create quotes and estimates which include, but are not limited to, parts and labor.	
04.0	Perform basic welding skills.--The student will be able to:	
04.01	Set up and operate gas and electric various welding equipment.	
04.02	Burn (cut) material using mechanized or hand-held gas torch equipment.	
04.03	Prepare metal surfaces for welding.	
04.04	Identify type of metal to be welded.	
04.05	Fabricate metal frames and structures.	
04.06	Pressure test weldment.	
04.07	Perform various advanced welding techniques.	
04.08	Describe techniques used to gas weld ferrous metals with or without filler rod.	
04.09	Perform Gas tungsten arc welding (GTAW) on ferrous and non-ferrous metals.	
04.10	Maintain a variety of welding equipment.	
04.11	Use welding principles to heat and remove broken screws and bolts.	
04.12	Identify five basic welding joints.	
04.13	Perform shielded metal arc welding (SMAW) on ferrous metals.	
05.0	Remove and install engines.--The student will be able to:	
05.01	Disconnect engine, mounts, wiring and lines.	
05.02	Operate engine hoist.	
05.03	Install and rig engines according to manufacturer’s specifications.	
05.04	Cut openings for different engine installations.	
05.05	Describe the operation and mounting procedures of a propulsion unit.	
05.06	Align (gas and diesel) engines to manufacturers' specifications.	
06.0	Recondition and service engines.--The student will be able to:	
06.01	Remove and replace power head.	
06.02	Disassemble engine.	
06.03	Clean engine parts for inspection.	
06.04	Inspect and check for proper condition.	
06.05	Remove and install oil pump.	
06.06	Remove and install fuel pump.	
06.07	Remove and install connecting rods and bearings.	
06.08	Remove and install flywheel.	
06.09	Remove and install exhaust manifolds and risers.	
06.10	Perform cylinder compression test.	
06.11	Perform engine tune up.	
06.12	Perform operational inspection of engine lubrication system.	
06.13	Remove and service piston ring and pistons.	
06.14	Fit piston pins.	
06.15	Inspect crankshaft, camshaft, connecting rods and piston assembly.	
06.16	Complete inspection of the head with different methods, replace valve springs and seals, and grinding of cylinder head seats and valves.	
06.17	Torque power head and lower unit to specifications.	
06.18	Hone cylinders to manufacturers' specifications.	
07.0	Perform diagnosis service and repairs for all types of marine ignition systems.--The student will be able to:	
07.01	Diagnose, repair and replace malfunctions of ignition system components.	
07.02	Set ignition timing.	
07.03	Inspect secondary circuit lead wires, distributor and rotor measure resistance in secondary wires.	
07.04	Analyze or adjust engine performance using engine computer diagnostic software.	
07.05	Remove and replace spark plugs.	
07.06	Time the ignition system for marine engines.	
07.07	Use specialized test equipment.	
07.08	Test CD type ignition systems.	
07.09	Describe differences between marine and automotive type ignition components.	
07.10	Read and interpret manufacturers wire diagrams.	
08.0	Develop skills in electrical-electronic theory of operation and application.--The student will be able to:	
08.01	Apply Ohm's Law to series circuit.	
08.02	Apply Ohm's Law to parallel circuits.	
08.03	Apply Ohm's Law to series-parallel circuits.	
08.04	Perform continuity test.	
08.05	Describe the theory and operation of alternators.	
08.06	Diagnose and repair or replace charging system regulator.	
08.07	Service or replace battery cables and battery box.	
08.08	Diagnose, repair or replace starter.	
08.09	Diagnose and repair malfunctions in the cranking system.	
08.10	Perform operational inspection of lighting system.	
08.11	Measure voltage drops, current flow, resistance in a circuit or component with a multi-meter.	
08.12	Repair or replace switches to include ignition switches.	
08.13	Repair or replace fuse block assembly.	
08.14	Locate and repair shorts and open circuits in wiring.	
08.15	Inspect or replace rectifier.	
08.16	Replace diode assembly.	
08.17	Remove, replace, and repair digital electronic control assembly.	
08.18	Service and install diesel and gasoline marine alarm systems.	
08.19	Locate and match electrical units by their symbols on a wiring diagram.	
09.0	Troubleshoot and repair fuel systems.--The student will be able to:	
09.01	Identify fuel system components.	
09.02	Explain operation of fuel system and components.	
09.03	Describe carburation theory and operation.	
09.04	Repair gasoline injection systems.	
09.05	Replace fuel system components.	
09.06	Identify fuel systems malfunction.	
09.07	Replace fuel filter.	
09.08	Repair fuel lines.	
09.09	Service automatic or manual choke.	
09.10	Service fuel pump.	
09.11	Analyze fuel systems for foreign particles.	
09.12	Correct fuel tank installation.	
09.13	Test engines fuel flow using manufacturers' procedures and test equipment.	
09.14	Identify fuel specification for outboard motors, four-cycle engines, and diesel applications.	
09.15	Understand the operation of diesel fuel injector nozzles.	
09.16	Understand the operation of diesel fuel pumps.	
09.17	Introduce operation and adjustment procedures of unit injectors.	
09.18	Introduce the correct procedure and timing of fuel injector pumps.	
09.19	Understand how to conduct diesel fuel pressure test	
09.20	Introduce operation of the fuel rack on multiple plunger fuel injection pumps.	
10.0	Service cooling systems.--The student will be able to:	
10.01	Check engine temperature.	
10.02	Test thermostat.	
10.03	Inspect and/or replace water pump.	
10.04	Inspect and/or replace circulating water pump.	
10.05	Pressure test cooling system.	
10.06	Remove, clean, and replace cooling system parts.	
10.07	Inspect and repair heat exchanges on gasoline and marine diesel engine.	
10.08	Describe the operation and maintenance of marine keel coolers.	
10.09	Identify different types of approved coolant used in marine closed cooling systems.	
10.10	Check engine block cooling passages for corrosion and build-up.	
11.0	Service exhaust systems.--The student will be able to:	
11.01	Remove, inspect and replace an exhaust housing.	
11.02	Remove, inspect and replace inner exhaust housing.	
11.03	Remove, inspect and replace seal.	
11.04	Remove, inspect and replace aft exhaust cover.	
11.05	Remove, inspect and replace rubber mount.	
11.06	Remove, inspect and replace clamp.	
11.07	Remove, inspect and replace mount cover.	
11.08	Remove, inspect and replace water tube.	
11.09	Inspect service turbo charger.	
11.10	Recommend correct exhaust tubing for different marine applications.	
11.11	Service marine water cooled exhaust systems.	
11.12	Determine back pressure and exhaust applications.	
12.0	Repair drive systems.--The student will be able to:	
12.01	Inspect gear housing assembly.	
12.02	Determine fluid levels.	
12.03	Adjust gear linkages.	
12.04	Torque mounting bolts.	
12.05	Inspect drive shaft.	
12.06	Lubricate universal joint.	
12.07	Inspect gimbal bearing.	
12.08	Measure drive shaft angle and runout.	
12.09	Replace power transmission system.	
12.10	Rebuild power transmission.	
12.11	Correctly apply manufacturers' procedures in shimming and adjusting operations.	
13.0	Rig boats.--The student will be able to:	
13.01	Install engine steering components.	
13.02	Install and service electrical wiring harness.	
13.03	Install trim tabs on outboard and stern drives, both electrical and hydraulic type.	
13.04	List methods of outboard motor transom bracket installation.	
13.05	Describe and illustrate correct lighting/wiring procedures.	
13.06	Install engine remote control to manufacturers' specifications.	
14.0	Repair lower units.--The student will be able to:	
14.01	Replace lower unit gear lube.	
14.02	Pressure and vacuum test lower unit.	
14.03	Lubricate transom steering busing, cables, etc.	
14.04	Inspect, clean and lubricate propeller shaft.	
14.05	Inspect and install propeller.	
14.06	Inspect, remove and replace vertical drive gear.	
14.07	Remove, inspect and replace clutch dog.	
14.08	Remove, inspect and replace drive shaft pinion.	
14.09	Remove, inspect and replace lower unit seals.	
14.10	Remove and replace swivel bracket.	
14.11	Remove, inspect and replace forward and reverse driving gears.	
14.12	Remove, inspect and replace drive shaft and components.	
14.13	Remove, inspect and replace hydraulic pump, shaft rod end plunger.	
14.14	Adjust trim tab.	
14.15	Inspect and replace U-joints.	
14.16	Inspect and repair or replace lower unit lock.	
14.17	Remove, replace and repair tilt assemblies to include hydraulic tilt.	
14.18	Correctly shim lower units to engine manufacturer's specifications.	
14.19	Disassemble/reassemble stern drive gear cases.	
14.20	Disassemble/inspect/service/reassemble inboard marine transmissions both gasoline and diesel.	
14.21	Calculate torque and gear ratio.	
14.22	Identify major engine manufactures’ types of gear arrangements in today’s market	
14.23	Explain operation theory of mechanical shifting, electric shifting, and hydroelectric shifting.	
14.24	Identify the major parts of these shifting mechanisms.	
14.25	Understand by examination the principles of marine propulsion propeller theory.	
14.26	Demonstrate an understanding of lower unit operations and installation.	
14.27	Handle lifting devices properly.	
14.28	Diagnose planetary gear principle of operation and theory.	
15.0	Perform corrosion experiments and understand corrosion control.--The student will be able to:	
15.01	Identify galvanic corrosion.	
15.02	Explain the use and function of the galvanic series.	
15.03	Understand corrosion and its prevention.	
15.04	Demonstrate a basic knowledge of electricity.	
15.05	Identify difference in corrosion and cavitation.	
15.06	Demonstrate cause of corrosion.	
15.07	Distinguish fatigue corrosion.	
15.08	Understand electrolysis and its causes of corrosions.	
15.09	Identify and prepare metals for protective coatings.	
15.10	Demonstrate theory of operation of impress currents.	
15.11	Show proper installation procedure of impress current unit onboard ship.	
15.12	Maintain records and diagnose impress current failure.	
15.13	Identify non-metallic corrosion.	
15.14	Define special tools used in the maintenance and testing of sacrificial anodes.	
15.15	Understand acrylic and styrene copolymer coating.	
15.16	List causes of stray current corrosion.	

Additional Information

Laboratory Activities

Laboratory investigations that include scientific inquiry, research, measurement, problem solving, emerging technologies, tools and equipment, as well as, experimental, quality, and safety procedures are an integral part of this career and technical program/course. Laboratory investigations benefit all students by developing an understanding of the complexity and ambiguity of empirical work, as well as the skills required to manage, operate, calibrate and troubleshoot equipment/tools used to make observations. Students understand measurement error; and have the skills to aggregate, interpret, and present the resulting data. Equipment and supplies should be provided to enhance hands-on experiences for students.

Career and Technical Student Organization (CTSO)

SkillsUSA is the intercurricular career and technical student organization for providing leadership training and reinforcing specific career and technical skills.  Career and Technical Student Organizations provide activities for students as an integral part of the instruction offered.  

Accommodations

Federal and state legislation requires the provision of accommodations for students with disabilities to meet individual needs and ensure equal access. Postsecondary students with disabilities must self-identify, present documentation, request accommodations if needed, and develop a plan with their counselor and/or instructors. Accommodations received in postsecondary education may differ from those received in secondary education. Accommodations change the way the student is instructed. Students with disabilities may need accommodations in such areas as instructional methods and materials, assignments and assessments, time demands and schedules, learning environment, assistive technology and special communication systems. Documentation of the accommodations requested and provided should be maintained in a confidential file.

Additional Resources

For additional information regarding articulation agreements, Bright Futures Scholarships, Fine Arts/Practical Arts Credit and Equivalent Mathematics and Equally Rigorous Science Courses please refer to:

http://www.fldoe.org/academics/career-adult-edu/career-tech-edu/program-resources.stml