2019 - 2020
Florida Department of Education
Curriculum Framework 

Program Title:	Automotive CNG / LPG Technology
Program Type:	Career Preparatory
Career Cluster:	Transportation, Distribution and Logistics

Career Certificate Program – Career Preparatory	
Program Number	T401100	
CIP Number	0647060420	
Grade Level	30, 31	
Standard Length	1200 hours	
Teacher Certification	Refer to the Program Structure section	
CTSO	SkillsUSA	
SOC Codes (all applicable) 	49-3023 – Automotive Service Technicians and Mechanics	
CTE Program Resources 	http://www.fldoe.org/academics/career-adult-edu/career-tech-edu/program-resources.stml	
Basic Skills Level	Mathematics:	10
Language:	  9
Reading:	  9	

Purpose

This program offers a sequence of courses that provides coherent and rigorous content aligned with challenging academic standards and relevant technical knowledge and skills needed to prepare for further education and careers in the Transportation, Distribution and Logistics career cluster; provides technical skill proficiency, and includes competency-based applied learning that contributes to the academic knowledge, higher-order reasoning and problem-solving skills, work attitudes, general employability skills, technical skills, and occupation-specific skills, and knowledge of all aspects of the Transportation, Distribution and Logistics career cluster. 

The content includes but is not limited to broad, transferable skills and stresses understanding and demonstration of the following elements of the Automotive industry; planning, management, finance, technical and product skills, underlying principles of technology, labor issues, community issues and health, safety, and environmental issues.

Additional Information relevant to this Career and Technical Education (CTE) program is provided at the end of this document.

Program Structure

This program is a planned sequence of instruction consisting of five occupational completion points.

NOTE:  It is recommended that students complete OCP-A (Automobile Services Assistor) and/or demonstrate mastery of the outcomes in OCP-A (Automobile Services Assistor) prior to enrolling in additional Automotive CNG-LPG Technology courses. The sequence of OCP’s, after completing and/or demonstrating mastery of OCP-A (Automobile Services Assistor), is at the discretion of the instructor.

Benchmarks identified with a designation of P-1, P-2, or P-3 are ASE tasks.

When offered at the postsecondary level, this program is comprised of courses which have been assigned course numbers in the SCNS (Statewide Course Numbering System) in accordance with Section 1007.24 (1), F.S. Career and Technical credit shall be awarded to the student on a transcript in accordance with Section 1001.44 (3) (b), F.S.

To teach the course(s) listed below, instructors must hold at least one of the teacher certifications indicated for that course.

The following table illustrates the postsecondary program structure:

OCP	Course Number	Course Title	Teacher Certification	Length	SOC Code	
A	AER0014	Automobile Services Assistor	AUTO IND @7 %7G
AUTO MECH @7 7G	300 hours	49-3023	
B	AER0360	Automotive Electrical/Electronic System Technician		300 hours	49-3023	
C	AER0503	Automotive Engine Performance Technician		300 hours	49-3023	
D	AER0871	Automotive Compressed Natural Gas Technician		150 hours	49-3023	
E	AER0872	Automotive Liquid Propane Gas Technician		150 hours	49-3023	

National Standards

Industry or National Standards corresponding to the standards and/or benchmarks for the Automotive CNG / LPG Technology program can be found using the following link: 

http://www.aseeducation.org/program-accreditation

Common Career Technical Core – Career Ready Practices

Career Ready Practices describe the career-ready skills that educators should seek to develop in their students. These practices are not exclusive to a Career Pathway, program of study, discipline or level of education. Career Ready Practices should be taught and reinforced in all career exploration and preparation programs with increasingly higher levels of complexity and expectation as a student advances through a program of study.

1. Act as a responsible and contributing citizen and employee.

2. Apply appropriate academic and technical skills.

3. Attend to personal health and financial well-being.

4. Communicate clearly, effectively and with reason.

5. Consider the environmental, social and economic impacts of decisions.

6. Demonstrate creativity and innovation.

7. Employ valid and reliable research strategies.

8. Utilize critical thinking to make sense of problems and persevere in solving them.

9. Model integrity, ethical leadership and effective management.

10. Plan education and career path aligned to personal goals.

11. Use technology to enhance productivity.

12. Work productively in teams while using cultural/global competence.

Standards

After successfully completing this program, the student will be able to perform the following:

01.0	Proficiently explain and apply required shop and personal safety tasks relating to the automotive industry.
02.0	Explain and apply required tasks associated with the proper use and handling of tools and equipment relating to the automotive industry.
03.0	Demonstrate proficiency in preparing vehicle for routine pre/post maintenance and customer services.
04.0	Explain and apply proficiently the diagnosis, service and repair of electrical/electronic system components, battery, starting, charging, lighting, gauges, warning devices, driver information, horn, wiper/washer and accessory systems.
05.0	Explain and apply proficiently the diagnosis, service and repair of engines, ignition, fuel, air induction, exhaust, computer, engine and emission control systems.
06.0	Explain and apply proficiently the diagnosis, service and repair of Compressed Natural Gas systems.
07.0	Explain and apply proficiently the diagnosis, service and repair of Liquid Propane Gas systems.

2019 - 2020
Florida Department of Education
Student Performance Standards

Program Title:	Automotive CNG / LPG Technology 
Career Certificate Program Number:	T401100

Course Number:  AER0014
Occupational Completion Point:  A
Automotive Services Assistor – 300 Hours – SOC Code 49-3023

Course Description: 
The Automotive Service Assistor course prepares students for entry into the automotive service industry. Students explore career opportunities and requirements of a professional auto mechanic. Students study equipment skills, safety regulations, routine maintenance, and customer service.

Abbreviations: 
ASE = Automotive Service Excellence task

For every task in Automotive Services Assistor course, the following safety requirement MUST be strictly enforced:

Comply with personal and environmental safety practices associated with clothing; eye protection; hand tools; power equipment; proper ventilation; and the handling, storage, and disposal of chemicals/materials in accordance with local, state, and federal safety and environmental regulations.

CTE Standards and Benchmarks	Priority Number	
01.0	Proficiently explain and apply required shop and personal safety tasks relating to the automotive industry.-The student will be able to:		
01.01	Identify and apply general shop safety rules and procedures, EPA and OSHA standards.	ASE	
01.02	Demonstrate knowledge of appropriate automotive industry certifications.		
01.03	Identify and define career opportunities in the automotive service industry.		
01.04	Research, identify, and interpret the Federal Law as recorded in (29 CFR-1910.1200).		
01.05	Identify appropriate emergency first aid procedures.		
01.06	Utilize and demonstrate safe procedures for handling of tools and equipment.	ASE	
01.07	Identify and use proper placement of floor jacks and jack stands. 	ASE	
01.08	Identify and use proper procedures for safe lift operation. 	ASE	
01.09	Utilize proper ventilation procedures for working within the lab/shop area.	ASE	
01.10	Identify proper procedures for safe pit usage.		
01.11	Identify marked safety areas.	ASE	
01.12	Identify the location and the types of fire extinguishers and other fire safety equipment.	ASE	
01.13	Demonstrate knowledge of the procedures for using fire extinguishers and other safety equipment.	ASE	
01.14	Identify the location and use of eye wash stations.	ASE	
01.15	Identify the location of the posted evacuation routes.	ASE	
01.16	Comply with the required use of safety glasses, ear protection, gloves, and shoes during lab/shop activities.	ASE	
01.17	Identify and wear appropriate clothing for lab/shop activities.	ASE	
01.18	Secure hair and jewelry for lab/shop activities.	ASE	
01.19	Use proper handling procedures for automotive fluids.		
01.20	Identify and describe typical automotive lubricants and lubricant properties.		
01.21	Identify and describe typical automotive seals and gaskets.		
01.22	Demonstrate awareness of the safety aspects of supplemental restraint systems (SRS), electronic brake control systems, and hybrid vehicle high voltage circuits.	ASE	
01.23	Disable supplemental restraint systems (SRS) in accordance with manufacturers' procedures.		
01.24	Demonstrate awareness of the safety aspects of high voltage circuits (such as high intensity discharge (HID) lamps, ignition systems, injection systems, etc.)	ASE	
01.25	Locate and demonstrate knowledge of Safety Data Sheets (SDS).	ASE	
02.0	Explain and apply required tasks associated with the proper use and handling of tools and equipment relating to the automotive industry.-The student will be able to:		
02.01	Identify tools and equipment and their appropriate usage in automotive applications.	ASE	
02.02	Identify and use standard and metric measurement skills and designation.	ASE	
02.03	Demonstrate proper cleaning, storage, and maintenance of tools and equipment.	ASE	
02.04	Demonstrate proper use of precision-measuring tools (i.e. micrometer, digital/dial-indicator, digital/dial caliper) and torque methods.	ASE	
03.0	Demonstrate proficiency in preparing vehicle for routine pre/post maintenance and customer services.-The student will be able to:		
03.01	Identify information needed and the service requested on a repair order.	ASE	
03.02	Identify automobiles according to engine location, cylinders, type of drive system, purpose, etc.		
03.03	Identify purpose and demonstrate proper use of fender covers, floor mats and other vehicle protection equipment.	ASE	
03.04	Demonstrate use of the three C's (Concern, Cause, and Correction).	ASE	
03.05	Review vehicle service history.	ASE	
03.06	Complete work order to include customer information, vehicle identifying information, customer concern, related service history, cause, and correction.	ASE	
03.07	Conduct an appropriate pre-service evaluation and report or note any concerns not already on the repair order.		
03.08	Determine the presence of a Tire Pressure Monitoring System (TPMS).		
03.09	Determine the presence of wheel locks.		
03.10	Determine the presence of an air suspension system. 		
03.11	Check operation and status of instrument panel warning lights and gauges. 		
03.12	Locate and use Vehicle identification Number (VIN) vehicle information placards, decals, tags, as required.		
03.13	Demonstrate proficiency in manufacturer electronic service information system, including flat rate manuals, technical service bulletins and replacement part identification; where applicable.		
03.14	Use proper chemicals for cleaning and lubrication.		
03.15	Reset maintenance indicators; as applicable. 		
03.16	Ensure vehicle is prepared to return to customer per school/company policy (floor mats, steering wheel cover, etc.).	ASE	
03.17	Inspect under-hood area for leaks, damage, and unusual conditions. 		
03.18	Determine fluid type requirements and identify fluid.		
03.19	Check engine oil level and condition; service as required.		
03.20	Check engine coolant level and condition; service as required. 		
03.21	Check power steering fluid level and condition; service as required.		
03.22	Check brake fluid level and condition; service as required.		
03.23	Check hydraulic clutch fluid and condition; service as required. 		
03.24	Check windshield washer fluid level and condition; service as required. 		
03.25	Check automatic transmission fluid level and condition; service as required.		
03.26	Inspect undercar area for leaks, damage, and unusual conditions.		
03.27	Check differential/transfer case fluid level; note unusual conditions; service as required.		
03.28	Check manual transmission fluid level; note unusual conditions; service as required. 		
03.29	Inspect brake lines, flexible hoses, and fittings for leaks, dents, kinks, rust, cracks, bulging or wear. 		
03.30	Lubricate driveline, suspension and steering systems; as applicable. 		
03.31	Inspect cooling system pipes and hoses for wear, damage, and proper routing. 		
03.32	Change engine oil and filter. 		
03.33	Inspect and replace fuel filters; as applicable. 		
03.34	Inspect and replace air filter. 		
03.35	Inspect and replace cabin air filter. 		
03.36	Inspect, replace and adjust drive belts; inspect tensioners and pulleys. 		
03.37	Document observed damage, unusual conditions, and concerns. 		
03.38	Inspect struts, springs, and related components; service as required. 		
03.39	Inspect stabilizer bar, bushings, brackets, and links; service as required. 		
03.40	Inspect springs, torsion bars, and related components; service as required. 		
03.41	Inspect shock absorbers and related components. 		
03.42	Inspect constant velocity (CV) axle shaft boots; service as required. 		
03.43	Identify service considerations when equipped with a Tire Pressure Monitoring System (TPMS). 		
03.44	Identify nitrogen-filled tires.  		
03.45	Inspect tires, diagnose tire wear patterns, inspect spare and mounting system; check and adjust tire pressure; where applicable. 		
03.46	Rotate tires according to manufacturer’s recommendations. 		
03.47	Balance wheel and tire assembly (static, dynamic and road force balance); where applicable. 		
03.48	Dismount, inspect, and remount tire on wheel. 		
03.49	Repair tire according to industry standards. 		
03.50	Reinstall wheel; torque wheel fasteners to specification.		
03.51	Check wheel bearings for play and other signs of wear. 		
03.52	Perform a visual inspection of a brake drum system. 		
03.53	Perform a visual inspection of a disc brake system. 		
03.54	Check parking brake operation; check parking brake components for unusual conditions.  		
03.55	Check wiper blades, inserts, and arms; replace wiper blades or inserts. 		
03.56	Lubricate door latches and hinges. 		
03.57	Inspect fuel tank, fuel cap and seal; inspect and replace fuel lines, fittings, and hoses; as applicable. 		
03.58	Perform slow/fast battery charge. 		
03.59	Inspect and clean battery cables, connectors, clamps, and hold-downs; repair or replace as needed.		
03.60	Perform battery, starting, and charging system tests using appropriate tester. 		
03.61	Start a vehicle using jumper cables or a battery auxiliary power supply (jump box).		
03.62	Maintain or restore electronic memory functions if required. 		
03.63	Inspect and test fusible links, circuit breakers, and fuses; confirm proper circuit operation; replace as needed.		
03.64	Inspect and replace exterior and courtesy lamps. 		

2019 - 2020

Florida Department of Education
Student Performance Standards

Course Number:  AER0360
Occupational Completion Point:  B
Automotive Electrical/Electronic System Technician – 300 Hours – SOC Code 49-3023

Course Description: 
The Automotive Electrical/Electronic System Technician prepares students for entry into the automotive service industry. Students explore career opportunities and requirements of a professional auto mechanic. Students study diagnostics and repair of electrical/electronics, battery, starting, charging, lighting, gauges, warning devices, driver information, horn, wiper/washer and accessory systems.

Abbreviations: 
EE = Electrical/Electronic Systems

EE Task List:
P-1 = 30
P-2 = 16
P-3 =   1
Total	          47

For every task in Automotive Electrical/Electronic System Technician course, the following safety requirement MUST be strictly enforced:

Comply with personal and environmental safety practices associated with clothing; eye protection; hand tools; power equipment; proper ventilation; and the handling, storage, and disposal of chemicals/materials in accordance with local, state, and federal safety and environmental regulations.

CTE Standards and Benchmarks	Priority Number	
04.0	Explain and apply proficiently the diagnosis, service and repair of electrical/electronic system components, battery, starting, charging, lighting, gauges, warning devices, driver information, horn, wiper/washer and accessory systems.-The student will be able to:		
General: Electrical System Diagnosis		
04.01	Research vehicle service information including vehicle service history, service precautions, and technical service bulletins.	P-1	
04.02	Demonstrate knowledge of electrical/electronic series, parallel, and series-parallel circuits using principles of electricity (Ohm’s Law).	P-1	
04.03	Demonstrate proper use of a digital multi-meter (DMM) when measuring source voltage, voltage drop (including grounds), current flow and resistance.	P-1	
04.04	Demonstrate knowledge of the causes and effects from shorts, grounds, opens, and resistance problems in electrical/electronic circuits.	P-1	
04.05	Demonstrate proper use of a test light on an electrical circuit.	P-1	
04.06	Use fused jumper wires to check operation of electrical circuits.	P-1	
04.07	Use wiring diagrams during the diagnosis (troubleshooting) of electrical/electronic circuit problems.	P-1	
04.08	Diagnose the cause(s) of excessive key-off battery drain (parasitic draw); determine needed action.	P-1	
04.09	Inspect and test fusible links, circuit breakers, and fuses; determine needed action.	P-1	
04.10	Inspect, test, repair, and/or replace components, connectors, terminals, harnesses, and wiring in electrical/electronic systems (including solder repairs); determine needed action.	P-1	
04.11	Check electrical/electronic circuit waveforms; interpret readings and determine needed repairs.	P-2	
04.12	Repair data bus wiring harness.	P-1	
04.13	Identify and interpret electrical/electronic system concern; determine necessary action.		
04.14	Identify location of hybrid vehicle high voltage circuit disconnect (service plug) location and safety procedures.		
Battery Diagnosis and Service		
04.15	Perform battery state-of-charge test; determine needed action.	P-1	
04.16	Confirm proper battery capacity for vehicle application; perform battery capacity and load test; determine needed action.	P-1	
04.17	Maintain or restore electronic memory functions.	P-1	
04.18	Inspect and clean battery; fill battery cells; check battery cables, connectors, clamps, and hold-downs.	P-1	
04.19	Perform slow/fast battery charge according to manufacturer’s recommendations.	P-1	
04.20	Jump-start vehicle using jumper cables and a booster battery or an auxiliary power supply.	P-1	
04.21	Identify safety precautions for high voltage systems on electric, hybrid, hybrid-electric, and diesel vehicles.	P-2	
04.22	Identify electrical/electronic modules, security systems, radios, and other accessories that require re-initialization or code entry after reconnecting vehicle battery.	P-1	
04.23	Identify hybrid vehicle auxiliary (12v) battery service, repair, and test procedures.	P-2	
04.24	Perform battery conductance test; determine necessary action.		
Starting System Diagnosis and Repair		
04.25	Perform starter current draw tests; determine needed action.	P-1	
04.26	Perform starter circuit voltage drop tests; determine needed action.	P-1	
04.27	Inspect and test starter relays and solenoids; determine needed action.	P-2	
04.28	Remove and install starter in a vehicle.	P-1	
04.29	Inspect and test switches, connectors, and wires of starter control circuits; determine needed action.	P-2	
04.30	Differentiate between electrical and engine mechanical problems that cause a slow-crank or a no-crank condition.	P-2	
04.31	Demonstrate knowledge of an automatic idle-stop/start-stop system.	P-2	
Charging System Diagnosis and Repair		
04.32	Perform charging system output test; determine needed action.	P-1	
04.33	Diagnose (troubleshoot) charging system for causes of undercharge, no-charge, or overcharge conditions.	P-1	
04.34	Inspect, adjust, and/or replace generator (alternator) drive belts; check pulleys and tensioners for wear; check pulley and belt alignment.	P-1	
04.35	Remove, inspect, and/or replace generator (alternator).	P-1	
04.36	Perform charging circuit voltage drop tests; determine needed action.	P-1	
Lighting Systems Diagnosis and Repair		
04.37	Diagnose (troubleshoot) the causes of brighter-than-normal, intermittent, dim, or no light operation; determine needed action.	P-1	
04.38	Inspect interior and exterior lamps and sockets including headlights and auxiliary lights (fog lights/driving lights); replace as needed.	P-1	
04.39	Aim headlights.	P-2	
04.40	Identify system voltage and safety precautions associated with high-intensity discharge headlights.	P-2	
04.41	Inspect and diagnose incorrect turn signal or hazard light operation; perform necessary action.		
Instrument Cluster and Driver Information Systems Diagnosis and Repair		
04.42	Inspect and test gauges and gauge sending units for causes of abnormal readings; determine needed action.	P-2	
04.43	Diagnose (troubleshoot) the causes of incorrect operation of warning devices and other driver information systems; determine needed action.	P-2	
04.44	Reset maintenance indicators as required.	P-2	
04.45	Inspect and test sensors, connectors, and wires of electronic (digital) instrument circuits; determine necessary action.		
Body Electrical Systems Diagnosis and Repair		
04.46	Diagnose operation of comfort and convenience accessories and related circuits (such as: power window, power seats, pedal height, power locks, truck locks, remote start, moon roof, sun roof, sun shade, remote keyless entry, voice activation, steering wheel controls, back-up camera, park assist, cruise control, and auto dimming headlamps); determine needed repairs.	P-2	
04.47	Diagnose operation of security/anti-theft systems and related circuits (such as: theft deterrent, door locks, remote keyless entry, remote start, and starter/fuel disable); determine needed repairs.	P-2	
04.48	Diagnose operation of entertainment and related circuits (such as: radio, DVD, remote CD changer, navigation, amplifiers, speakers, antennas, and voice-activated accessories); determine needed repairs.	P-3	
04.49	Diagnose operation of safety systems and related circuits (such as:  horn, airbags, seat belt pretensioners, occupancy classification, wipers, washers, speed control/collision avoidance, heads-up display, park assist, and back-up camera); determine needed repairs.	P-1	
04.50	Diagnose body electronic systems circuits using a scan tool; check for module communication errors (data communication bus systems); determine needed action.	P-2	
04.51	Describe the process for software transfer, software updates, or reprogramming of electronic modules.	P-2	
04.52	Diagnose incorrect heated glass, mirror, or seat operation; determine necessary action.		

2019 - 2020

Florida Department of Education
Student Performance Standards

Course Number:  AER0503
Occupational Completion Point:  C
Automotive Engine Performance Technician – 300 Hours – SOC Code 49-3023

Course Description: 
The Automotive Engine Performance Technician course prepares students for entry into the automotive service industry. Students explore career opportunities and requirements of a professional auto mechanic. Students study the diagnosis, service and repair of engines, ignition, fuel, air induction, exhaust, computer, engine and emission control systems.

Abbreviations: 
EP = Engine Performance

EP Task List:
P-1 = 21
P-2 = 20
P-3 =   2
Total	          43

For every task in Automotive Engine Performance Technician course, the following safety requirement MUST be strictly enforced:

Comply with personal and environmental safety practices associated with clothing; eye protection; hand tools; power equipment; proper ventilation; and the handling, storage, and disposal of chemicals/materials in accordance with local, state, and federal safety and environmental regulations.

CTE Standards and Benchmarks	Priority Number	
05.0	Explain and apply proficiently the diagnosis, service and repair of engines, ignition, fuel, air induction, exhaust, computer engine and emission control systems.-The student will be able to:		
General: Engine Diagnosis		
05.01	Identify and interpret engine performance concerns; determine needed action.	P-1	
05.02	Research vehicle service information including vehicle service history, service precautions, and technical service bulletins.	P-1	
05.03	Diagnose abnormal engine noises or vibration concerns; determine needed action.	P-3	
05.04	Diagnose the cause of excessive oil consumption, coolant consumption, unusual exhaust color, odor, and sound; determine needed action.	P-2	
05.05	Perform engine absolute manifold pressure tests (vacuum/boost); determine needed action.	P-1	
05.06	Perform cylinder power balance test; determine needed action.	P-2	
05.07	Perform cylinder cranking and running compression tests; determine needed action.	P-1	
05.08	Perform cylinder leakage test; determine needed action.	P-1	
05.09	Diagnose engine mechanical, electrical, electronic, fuel, and ignition concerns; determine needed action.	P-2	
05.10	Verify engine operating temperature; determine needed action.	P-1	
05.11	Verify correct camshaft timing including engines equipped with variable valve timing systems (VVT).	P-1	
05.12	Inspect engine assembly for fuel, oil, coolant, and other leaks; determine necessary action.			
05.13	Demonstrate knowledge of using a 4 or 5 gas analyzer, interpret readings, and determine necessary action.		
05.14	Perform cooling system pressure tests; check coolant condition; inspect and test radiator, pressure cap, coolant recovery tank, and hoses; perform necessary action.		
Computerized Controls Diagnosis and Repair		
05.15	Retrieve and record diagnostic trouble codes (DTC), OBD monitor status, and freeze frame data; clear codes when applicable.	P-1	
05.16	Access and use service information to perform step-by-step (troubleshooting) diagnosis.	P-1	
05.17	Perform active tests of actuators using a scan tool; determine needed action.	P-1	
05.18	Describe the use of OBD monitors for repair verification.	P-1	
05.19	Diagnose the causes of emissions or drive-ability concerns with stored or active diagnostic trouble codes (DTC); obtain, graph, and interpret scan tool data.	P-1	
05.20	Diagnose emissions or drive-ability concerns without stored or active diagnostic trouble codes; determine needed action.	P-1	
05.21	Inspect and test computerized engine control system sensors, powertrain/engine control module (PCM/ECM), actuators, and circuits using a graphing multi-meter (GMM)/digital storage oscilloscope (DSO); perform needed action.	P-2	
05.22	Diagnose drive-ability and emissions problems resulting from malfunctions of interrelated systems (cruise control, security alarms, suspension controls, traction controls, HVAC, automatic transmissions, non-OEM installed accessories, or similar systems); determine needed action.	P-2	
05.23	Check for module communication (including CAN/BUS systems) errors using a scan tool.		
Ignition System Diagnosis and Repair		
05.24	Diagnose (troubleshoot) ignition system related problems such as no-starting, hard starting, engine misfire, poor drive-ability, spark knock, power loss, poor mileage, and emissions concerns; determine needed action.	P-2	
05.25	Inspect and test crankshaft and camshaft position sensor(s); determine needed action.	P-1	
05.26	Inspect, test, and/or replace ignition control module, powertrain/engine control module; reprogram/initialize as needed.	P-3	
05.27	Remove and replace spark plugs; inspect secondary ignition components for wear and damage.	P-1	
05.28	Inspect and test ignition primary and secondary circuit wiring and solid state components; test ignition coil(s); perform necessary action.		
Fuel, Air Induction, and Exhaust Systems Diagnosis and Repair		
05.29	Diagnose (troubleshoot) hot or cold no-starting, hard starting, poor drive-ability, incorrect  idle speed, poor idle, flooding, hesitation, surging, engine misfire, power loss, stalling, poor mileage, dieseling, and emissions problems; determine needed action.	P-2	
05.30	Check fuel for contaminants; determine needed action.	P-2	
05.31	Inspect and test fuel pump(s) and pump control system for pressure, regulation, and volume; perform needed action.	P-1	
05.32	Replace fuel filter(s) where applicable.	P-2	
05.33	Inspect, service, or replace air filters, filter housings, and intake duct work.	P-1	
05.34	Inspect throttle body, air induction system, intake manifold and gaskets for vacuum leaks and/or unmetered air.	P-2	
05.35	Inspect, test, and/or replace fuel injectors.	P-2	
05.36	Verify idle control operation. 	P-1	
05.37	Inspect integrity of the exhaust manifold, exhaust pipes, muffler(s), catalytic converter(s), resonator(s), tail pipe(s), and heat shields; perform needed action.	P-1	
05.38	Inspect condition of exhaust system hangers, brackets, clamps, and heat shields; determine needed action.	P-1	
05.39	Perform exhaust system back-pressure test; determine needed action.	P-2	
05.40	Check and refill diesel exhaust fluid (DEF).	P-2	
05.41	Test the operation of turbocharger/supercharger systems; determine needed action.	P-2	
Emissions Control Systems Diagnosis and Repair		
05.42	Diagnose oil leaks, emissions, and drive-ability concerns caused by the positive crankcase ventilation (PCV) system; determine needed action.	P-3	
05.43	Inspect, test, service, and/or replace positive crankcase ventilation (PCV) filter/breather, valve, tubes, orifices, and hoses; perform needed action.	P-2	
05.44	Diagnose emissions and drive-ability concerns caused by the exhaust gas recirculation (EGR) system; inspect, test, service and/or replace electrical/electronic sensors, controls, wiring, tubing, exhaust passages, vacuum/pressure controls, filters, and hoses of exhaust gas recirculation (EGR) systems; determine needed action.	P-2	
05.45	Diagnose emissions and drive-ability concerns caused by the secondary air injection system; inspect, test, repair, and/or replace electrical/electronically-operated components and circuits of secondary air injection systems; determine needed action.	P-2	
05.46	Diagnose emissions and drive-ability concerns caused by the evaporative emissions control (EVAP) system; determine needed action.	P-1	
05.47	Diagnose emission and drive-ability concerns caused by catalytic converter system; determine needed action.	P-2	
05.48	Interpret diagnostic trouble codes (DTCs) and scan tool data related to the emissions control systems; determine needed action.	P-2	
05.49	Inspect and test mechanical components of secondary air injection systems; perform necessary action.		
05.50	Adjust valves on engines with mechanical or hydraulic lifters; as applicable.			
05.51	Remove and replace timing belt; verify correct camshaft timing.		
05.52	Inspect and test mechanical/electrical fans, fan clutch, fan shroud/ducting, air dams, and fan control devices; perform necessary action.		
05.53	Inspect engine oil and/or filter for condition and determine necessary action.		
05.54	Identify hybrid vehicle internal combustion engine service precautions.		

2019 - 2020

Florida Department of Education
Student Performance Standards

Course Number:  AER0871
Occupational Completion Point:  C
Automotive Compressed Natural Gas Technician – 150 Hours – SOC Code 49-3023

Course Description: 
The Automotive Compressed Natural Gas Technician course prepares students for entry into the automotive service industry. Students explore career opportunities and requirements of a professional auto mechanic. Students study the diagnosis, service, maintenance, installation, and repair of automotive compressed natural gas systems.

For every task in Automotive Compressed Natural Gas course, the following safety requirement MUST be strictly enforced:

Comply with personal and environmental safety practices associated with clothing; eye protection; hand tools; power equipment; proper ventilation; and the handling, storage, and disposal of chemicals/materials in accordance with local, state, and federal safety and environmental regulations.

CTE Standards and Benchmarks	
06.0	Explain and apply proficiently the diagnosis, service and repair of Compressed Natural Gas systems.-The student will be able to:	
06.01	Interpret and verify complaint, determine needed repairs for Supplemental Systems.	
06.02	Analyze symptoms and perform diagnostic procedures on vehicles with supplemental on-board diagnostic computer support systems.	
06.03	Diagnose and repair no starting, hard starting, engine misfire, poor drivability, power loss, poor mileage, and emissions problems on vehicle's OEM and supplemental sensors (e.g., manifold skin temperature, intake air temperature, and natural gas tank temperature).	
06.04	Diagnose and repair no-starting, hard starting, engine misfire, poor drivability, power loss, poor mileage, and emissions problems on vehicles with supplemental computer support systems.	
06.05	Diagnose and repair intermittent or complete failure of electric, electronic or mechanical devices (e.g., hour meters, fuel level indicators, fuel selection devices).	
06.06	Interpret and verify complaint; determine needed repairs to Fuel Storage and Delivery systems.	
06.07	Check all fuel system components to include fuel lock-off, valves, solenoids, manual shutoff, connections, fittings, hoses, and tubing for leaks, wear, installation and proper operation: repair/replace as needed.	
06.08	Diagnose the cause of abnormal fuel flow through fuel carrying component.	
06.09	Diagnose the cause of fuel odor or fuel loss by inspecting or testing the fuel supply system components such as valves, fuel supply container, pressure relief device (PRD), tubing and hoses; repair or replace as needed.	
06.10	Diagnose the cause of inaccurate fuel level indicator reading; service, adjust, repair as needed.	
06.11	Perform cylinder leakage test; determine necessary action.	
06.12	Diagnose engine mechanical, electrical, electronic, fuel, and ignition concerns; determine necessary action.	
06.13	Interpret and verify complaint; determine needed repairs AIF Management system.	
06.14	Verify engine operating temperature; determine necessary action.	
06.15	Perform cooling system pressure tests; check coolant condition; inspect and test radiator, pressure cap, coolant recovery tank, and hoses; perform necessary action.	
06.16	Diagnose hot or cold no-starting, hard starting, poor drivability, incorrect idle speed, poor idle, flooding, hesitation, surging, engine, misfire, power loss, stalling, poor mileage, and lean or rich mixture, problems on vehicles with variable or fixed venturi type fuel, and fumigation or infection type fuel systems; determine needed repairs.	
06.17	Inspect and test cold enrichment system components; adjust or replace as needed.	
06.18	Inspect and test fuel injectors; service or replace as needed.	
06.19	Inspect and test vacuum and electrical components and connections of fuel system; repair or replace as needed.	
06.20	Perform diagnostic procedures on vehicles with on-board computer/electronic fuel system support.	
06.21	Follow manufacturer's maintenance schedule to ensure fluids and lubricants are at proper levels and serviced with recommended products.	
06.22	Identify the process of recertification or replacement of fuel supply container(s) according to most current regulations (e.g., NGV-2, DOT); complete documentation; remove and replace fuel supply container, if required.	
06.23	Inspect fuel supply container(s) and brackets as it relates to certification: data plate, working pressures, fuel supply container damage, valves, bolts, torque specifications, and all sealing and venting equipment.	
06.24	Inspect air filters and fuel filter; service or replace as needed.	
06.25	Inspect and ensure that all required emission control devices are present and functional.	
06.26	Inspect, adjust, and test manual shut-off valve, service valve, check-valves, and solenoid valves; repair or replace as needed.	
06.27	Empty fuel supply container according to manufacturer's procedures and all local, state and federal regulations. (Local procedures will vary and extreme care must be exercised if using actual fuel. Use of inert gas is recommended for this task.).	
06.28	Inspect and test fuel selection system components; repair or replace as needed.	
06.29	Select and install swage, compression, flare, captive 0-ring, NPT, and other fittings using manufacturer's recommended sealants when required.	
06.30	Check for fuel system problems caused by fuel contamination.	
06.31	Check air/fuel system integrity (e.g., fuel leaks, air leaks, components compatibility/application); determine needed repairs.	
06.32	Inspect and test fuel pressure regulation system components; adjust, repair or replace as needed.	
06.33	Remove, clean, and reinstall throttle assemblies; adjust related linkages as needed.	
06.34	Check/adjust idle speed and fuel mixtures according to manufacturer's procedures.	
06.35	Perform safe fueling procedures and determine fuel level.	
06.36	Identify working pressures and demonstrate an understanding of fuel characteristics as they relate to temperature and fill procedures.	
06.37	Inspect the vehicle for pre-existing conditions that may adversely affect the performance of the vehicle.	
06.38	Document pre-conversion conditions and complete all necessary reports.	
06.39	Prepare vehicle for conversion according to manufacturer's directions.	
06.40	Install fuel supply container with mounting hardware, valving, shielding, fuel level indicator, and remote fill assembly, as needed, using manufacturer's specifications and required local, state and federal regulations.	
06.41	Install pressure relief device (PRD) and venting system.	
06.42	Install gas tight enclosure around valves and fittings, vent to the outside of the vehicle.	
06.43	Determine routing and protection of fuel line components according to industry standards.	
06.44	Prepare tubing using proper techniques for cutting, deburring, cleaning, and bending.	
06.45	Install tubing, piping, hose, and valves using appropriate chafing protection, mounting hardware, and protective shields, according to industry safety standards.	
06.46	Determine appropriate location and mounting of the regulators; install the regulators using mounting brackets, fuel lock, fittings, starting aids, control valves, cooling lines, and thermostat as required and according to manufacturer's specifications.	
06.47	Install fuel injection/carburetion or other fuel control components according to manufacturer's instructions.	
06.48	Install electrical/electronic components using OEM or manufacturer's wire connections and wiring diagrams, applying all safety precautions.	
06.49	Determine location of electrical components considering safety, serviceability, function, component protection, and esthetics according to manufacturer's specifications (when available).	
06.50	Inspect and test each installed component to ensure it is connected and positioned in a safe and effective manner.	
06.51	Purge and pressurize fuel system and check for system integrity through its maximum working pressure (leak test).	
06.52	Perform system setup procedures according to manufacturer's specifications.	
06.53	Fabricate brackets, shields, and braces according to accepted industry standards.	
06.54	Complete and affix required safety/information labels.	
06.55	Test vehicle for acceptable drivability and operation (on each fuel for dual fuel vehicles).	
06.56	Inspect and ensure that all required emissions control devices are present and functional; confirm that the vehicle emissions meet applicable local, state, and federal requirements.	
06.57	Perform pre and post conversion emissions evaluation.	

2019 - 2020

Florida Department of Education
Student Performance Standards

Course Number:  AER0872
Occupational Completion Point: E
Automotive Liquid Propane Gas Technician – 150 Hours – SOC Code 49-3023

Course Description: 
The Automotive Liquid Propane Gas Technician prepares students for entry into the automotive service industry. Students explore career opportunities and requirements of a professional auto mechanic. Students study diagnostics, maintenance, installation, and repair of automotive liquid propane gas systems. 

For every task in Liquid Propane Gas Technician course, the following safety requirement MUST be strictly enforced:

Comply with personal and environmental safety practices associated with clothing; eye protection; hand tools; power equipment; proper ventilation; and the handling, storage, and disposal of chemicals/materials in accordance with local, state, and federal safety and environmental regulations.

CTE Standards and Benchmarks	
07.0	Explain and apply proficiently the diagnosis, service and repair of Liquid Propane Gas systems.-The student will be able to:	
07.01	Analyze symptoms and perform diagnostic procedures on vehicles with supplemental on-board diagnostic computer support systems.	
07.02	Diagnose and repair no starting, hard starting, engine misfire, poor drivability, power loss, poor mileage, and emissions problems on vehicle's OEM and supplemental sensors (e.g., manifold skin temperature, intake air temperature, etc.).	
07.03	Diagnose and repair no-starting, hard starting, engine misfire, poor drivability, power loss, poor mileage, and emissions problems on vehicles with supplemental computer support systems (e.g., timing modification devices, ignition interrupt).	
07.04	Diagnose and repair intermittent or complete failure of electric, electronic or mechanical devices (e.g., hour meters, fuel level indicators, fuel selection devices).	
07.05	Check all fuel system components to include fuel lock-off, valves, solenoids, manual shutoff, connections, fittings, hoses and tubing for leaks, wear, installation and proper operation; repair or replace as needed.	
07.06	Diagnose the cause of abnormal fuel flow through fuel carrying component.	
07.07	Diagnose engine noises and vibrations; determine necessary action.	
07.08	Diagnose the cause of fuel odor or fuel loss by inspecting or testing the fuel supply system components such as valves, fuel supply container, pressure relief device (PRD), tubing and hoses; repair or replace as needed.	
07.09	Diagnose the cause of inaccurate fuel level indicator reading; service, adjust, repair or replace as needed.	
07.10	Diagnose hot or cold no-starting, hard starting, poor drivability, incorrect idle speed, poor idle, flooding, hesitation, surging, engine misfire, power loss, stalling, poor mileage, and lean or rich mixture problems on vehicles with fumigation or injection type fuel systems; determine needed repairs.	
07.11	Inspect and test cold enrichment system components; adjust or replace as needed.	
07.12	Inspect and test fuel injectors; service or replace as needed.	
07.13	Inspect and test vacuum and electrical components and connections of fuel system; repair or replace as needed.	
07.14	Remove and reinstall engine in an OBDII or newer vehicle; reconnect all attaching components and restore the vehicle to running condition.	
07.15	Perform diagnostic procedures on vehicles with on-board computer/electronic fuel system support.	
07.16	Follow manufacturer's maintenance schedule to ensure fluids and lubricants are at proper levels and serviced with recommended products.	
07.17	Identify the process of recertification or replacement of fuel supply container(s) according to most current regulations (e.g., DOD complete documentation; remove and replace fuel supply container, if required.	
07.18	Inspect fuel supply container(s) and brackets as it relates to certification: data plate, pressures, supply container fuel damage, valves, bolts, torque specifications, and all sealing and venting equipment.	
07.19	Inspect air filters and fuel filter; service or replace as needed.	
07.20	Inspect and ensure that all required emission control devices are present and functional.	
07.21	Inspect, adjust, and test manual shut-off valve, service valve, check-valves, and solenoid valves; repair or replace as needed.	
07.22	Empty fuel supply container according to manufacturer's procedures and all local, state and federal regulations. (Local procedures will vary and extreme care must be exercised.)	
07.23	Inspect and test fuel selection system components; repair or replace as needed.	
07.24	Select and install  flare, NPT, and other fittings using required sealants for LPG according to manufacturer's specifications.	
07.25	Check for fuel system problems caused by fuel contamination.	
07.26	Check air/fuel system integrity (e.g., fuel leaks, air leaks, components compatibility/application); determine needed repairs.	
07.27	Inspect and test fuel pressure regulation system components; Adjust, repair or replace as needed.	
07.28	Remove, clean, and reinstall throttle assemblies; adjust related linkages as needed.	
07.29	Check/adjust idle speed and fuel mixtures according to manufacturer's procedures.	
07.30	Perform safe fueling procedures and determine fuel level.	
07.31	Identify working pressures and demonstrate an understanding of fuel characteristics as they relate to temperature and fill procedures.	
07.32	Empty fuel system using industry practices or manufacturer's procedures and all local, state and federal regulations. (Local procedures will vary and extreme care must be exercised.)	
07.33	Inspect the vehicle for pre-existing conditions that may adversely affect the performance of the vehicle.	
07.34	Document pre-conversion conditions and complete all necessary reports.	
07.35	Prepare vehicle for conversion according to manufacturer's directions.	
07.36	Install fuel supply container with mounting hardware, valving, shielding, fuel level indicator, and remote fill assembly as needed, using manufacturer's  specifications and required local, state and federal regulations.	
07.37	Install pressure relief device (PRD) and venting system.	
07.38	Select and install flare, NPT, and other fittings using sealants for LPG according to manufacturer's specifications.	
07.39	Install gas tight enclosure around valves and fittings, vent to the outside of vehicle as required.	
07.40	Determine routing and protection of fuel line components according to industry standards.	
07.41	Prepare tubing using proper techniques for cutting, deburring cleaning, and bending.	
07.42	Install tubing, piping, hose, and valves using appropriate chafing protection, mounting hardware, and protective shields, according to industry safety standards.	
07.43	Determine appropriate location and mounting of the converter/regulator; install the converter/regulator using mounting brackets, fuel lock, fittings, starting aids, control valves, cooling lines, and thermostat as required and according to manufacturer's specifications.	
07.44	Install fuel injection/carburetion or other fuel control components according to manufacturer's instructions.	
07.45	Install electrical/electronic components using OEM or manufacturer's wire connections and wiring diagrams, applying all safety precautions.	
07.46	Determine location of electrical components considering safety, serviceability, function, component protection, and esthetics according to manufacturer's specifications (when available).	
07.47	Inspect and test each installed component to ensure it is connected and positioned in a safe and effective manner.	
07.48	Purge and pressurize fuel system and check for system integrity through its maximum working pressure (leak test).	
07.49	Perform system setup procedures according to manufacturer's specifications.	
07.50	Fabricate brackets, shields, and braces according to accepted industry standards.	
07.51	Complete and affix required safety/information labels.	
07.52	Test vehicle for acceptable drivability and operation (on each fuel for dual fuel vehicles).	
07.53	Inspect and ensure that all required emissions control devices are present and functional; confirm that the vehicle emissions meet applicable local, state, and federal requirements.	
07.54	Perform pre and post conversion emissions evaluation.	

Additional Information

Laboratory Activities

Laboratory investigations that include scientific inquiry, research, measurement, problem solving, emerging technologies, tools and equipment, as well as, experimental, quality, and safety procedures are an integral part of this career and technical program/course. Laboratory investigations benefit all students by developing an understanding of the complexity and ambiguity of empirical work, as well as the skills required to manage, operate, calibrate and troubleshoot equipment/tools used to make observations. Students understand measurement error; and have the skills to aggregate, interpret, and present the resulting data. Equipment and supplies should be provided to enhance hands-on experiences for students. 

Special Notes

Benchmarks identified with a designation of P-1, P-2, or P-3 are ASE tasks.

MyCareerShines is an interactive resource to assist students in identifying their ideal career and to enhance preparation for employment. Teachers are encouraged to integrate this resource into the program curriculum to meet the employability goals for each student.  Access MyCareerShines by visiting: www.mycareershines.org.

Career and Technical Student Organization (CTSO)

SkillsUSA is the intercurricular career and technical student organization(s) providing leadership training and reinforcing specific career and technical skills. Career and Technical Student Organizations provide activities for students as an integral part of the instruction offered. 

Cooperative Training – OJT

On-the-job training is appropriate but not required for this program.  Whenever offered, the rules, guidelines, and requirements specified in the OJT framework apply. 

Basic Skills

In a Career Certificate Program offered for 450 hours or more, in accordance with Rule 6A-10.040, F.A.C., the minimum basic skills grade levels required for postsecondary adult career and technical students to complete this program are: Mathematics 10.0, Language 9.0, and Reading 9.0. These grade level numbers correspond to a grade equivalent score obtained on a state designated basic skills examination.  

Adult students with disabilities, as defined in Section 1004.02(7), Florida Statutes, may be exempted from meeting the Basic Skills requirements (Rule 6A-10.040). Students served in exceptional student education (except gifted) as defined in s. 1003.01(3)(a), F.S., may also be exempted from meeting the Basic Skills requirement. Each school district and Florida College must adopt a policy addressing procedures for exempting eligible students with disabilities from the Basic Skills requirement as permitted in Section 1004.91(3), F.S.

Students who possess a college degree at the Associate of Applied Science level or higher; who have completed or are exempt from the college entry-level examination; or who have passed a state, national, or industry licensure exam are exempt from meeting the Basic Skills requirement (Rule 6A-10.040, F.A.C.) Exemptions from state, national or industry licensure are limited to the certifications listed on the Basic Skills and Licensure Exemption List which may be accessed from the CTE Program Resources page.

Accommodations

Federal and state legislation requires the provision of accommodations for students with disabilities to meet individual needs and ensure equal access. Postsecondary students with disabilities must self-identify, present documentation, request accommodations if needed, and develop a plan with their counselor and/or instructors. Accommodations received in postsecondary education may differ from those received in secondary education. Accommodations change the way the student is instructed. Students with disabilities may need accommodations in such areas as instructional methods and materials, assignments and assessments, time demands and schedules, learning environment, assistive technology and special communication systems. Documentation of the accommodations requested and provided should be maintained in a confidential file.

Note: postsecondary curriculum and regulated secondary programs cannot be modified.

Additional Resources

For additional information regarding articulation agreements, Bright Futures Scholarships, Fine Arts/Practical Arts Credit and Equivalent Mathematics and Equally Rigorous Science Courses please refer to:

http://www.fldoe.org/academics/career-adult-edu/career-tech-edu/program-resources.stml