2015 - 2016
Florida Department of Education
Curriculum Framework 

Program Title:	Medium and Heavy Duty Truck and Bus Technician 2
Program Type:	Career Preparatory
Career Cluster:	Transportation, Distribution and Logistics

PSAV – Career Preparatory	
Program Number	T650200	
CIP Number	0647061306	
Grade Level	30, 31	
Standard Length	750 hours	
Teacher Certification	DIESEL MECH @7 7G	
CTSO	SkillsUSA	
SOC Codes (all applicable) 	49-3031 – Bus and Truck Mechanics and Diesel Engine Specialists	
CTE Program Resources 	http://www.fldoe.org/academics/career-adult-edu/career-tech-edu/program-resources.stml	
Basic Skills Level	Mathematics:	9
Language:	9
Reading:	9	

Purpose 

This program offers a sequence of courses that provides coherent and rigorous content aligned with challenging academic standards and relevant technical knowledge and skills needed to prepare for further education and careers in the Transportation, Distribution and Logistics career cluster; provides technical skill proficiency, and includes competency-based applied learning that contributes to the academic knowledge, higher-order reasoning and problem-solving skills, work attitudes, general employability skills, technical skills, and occupation-specific skills, and knowledge of all aspects of the Transportation, Distribution and Logistics career cluster. 

The content includes but is not limited to the following: maintaining and repairing diesel engines and electrical systems; reconditioning diesel fuel injection systems; overhauling diesel engines; and performing diesel engine preventive maintenance.

The course content should also include training in communication, leadership, human relations and employability skills; and safe efficient work practices.

Additional Information relevant to this Career and Technical Education (CTE) program is provided at the end of this document.

Program Structure

This program is a planned sequence of instruction consisting of five occupational completion points.

The courses may be taken in any sequence.  However, an individual must take the Diesel Engine Preventive Maintenance Technician course (DIM0103).  

When offered at the postsecondary level, this program is comprised of courses which have been assigned course numbers in the SCNS (Statewide Course Numbering System) in accordance with Section 1007.24 (1), F.S.  Career and Technical credit shall be awarded to the student on a transcript in accordance with Section 1001.44 (3)(b), F.S.

The following table illustrates the PSAV program structure:

OCP	Course Number	Course Title	Course Length	SOC Code	
A	DIM0103	Diesel Engine Preventative Maintenance Technician	150 hours	49-3031	
B	DIM0106	Diesel Heating and Air Conditioning Technician	150 hours	49-3031	
C	DIM0107	Diesel Steering and Suspension Technician	150 hours	49-3031	
D	DIM0108	Diesel Drivetrain Technician	150 hours	49-3031	
E	DIM0109	Diesel Hydraulics Technician	150 hours	49-3031	

National Standards

Programs identified as having Industry or National Standards corresponding to the standards and/or benchmarks for the Medium and Heavy Duty Bus and Truck program can be found using the following link:

http://www.natef.org/Achieving-Accreditation/Program-Standards.aspx

Common Career Technical Core – Career Ready Practices

Career Ready Practices describe the career-ready skills that educators should seek to develop in their students.  These practices are not exclusive to a Career Pathway, program of study, discipline or level of education.  Career Ready Practices should be taught and reinforced in all career exploration and preparation programs with increasingly higher levels of complexity and expectation as a student advances through a program of study. 

1. Act as a responsible and contributing citizen and employee. 

2. Apply appropriate academic and technical skills. 

3. Attend to personal health and financial well-being. 

4. Communicate clearly, effectively and with reason. 

5. Consider the environmental, social and economic impacts of decisions. 

6. Demonstrate creativity and innovation. 

7. Employ valid and reliable research strategies. 

8. Utilize critical thinking to make sense of problems and persevere in solving them. 

9. Model integrity, ethical leadership and effective management. 

10. Plan education and career path aligned to personal goals. 

11. Use technology to enhance productivity. 

12. Work productively in teams while using cultural/global competence. 

Standards

After successfully completing this program, the student will be able to perform the following:

01.0	Diagnose and repair engine systems.
01.01	Engine
01.02	Fuel system
01.03	Air induction and exhaust system
01.04	Cooling system
01.05	Lubrication system
02.0	Diagnose and repair cab and hood systems.
02.01	Instruments and controls
02.02	Safety equipment
02.03	Hardware
02.04	Heating, ventilation, and air conditioning (HVAC)
03.0	Diagnose and repair electrical/electronic systems.
03.01	Battery and starting systems
03.02	Charging system
03.03	Lighting system
04.0	Diagnose and repair frame and chassis systems.
04.01	Air brakes
04.02	Hydraulic brakes
04.03	Drivetrain
04.04	Suspension and steering systems
04.05	Tires and wheels 
04.06	Frame and fifth wheel
05.0	HVAC systems diagnosis, service, and repair.
06.0	A/C system and component diagnosis, service, and repair.
06.01	A/C system – general.
06.02	Compressor and clutch.
06.03	Evaporator, condenser, and related components.
06.04	Heating and engine cooling systems diagnosis, service, and repair.
07.0	Operating systems and related controls diagnosis and repair.
07.01	Electrical
07.02	Air/vacuum/mechanical
07.03	Refrigerant recovery, recycling, and handling.
08.0	Steering systems diagnosis and repair.
08.01	Steering column 
08.02	Steering units
08.03	Steering linkage
09.0	Suspension systems diagnosis and repair.
10.0	Wheel alignment diagnosis, adjustment, and repair. 
11.0	Wheels and tires diagnosis and repair.
12.0	Frame service and repair. 
13.0	Clutch diagnosis and repair.
14.0	Transmission diagnosis and repair.
15.0	Driveshaft and universal joint diagnosis and repair.
16.0	Drive axle diagnosis and repair.

For every task in Hydraulics, the following safety task must be strictly enforced:

Comply with personal and environmental safety practices associated with clothing; eye protection; hand protection; proper lifting practices; hand tools; power equipment; proper ventilation; and the handling, storage, and disposal of fuels/chemicals/materials in accordance with federal, state, and local regulations.

The first task in Hydraulics is to listen to and verify the operator’s concern, review past maintenance and repair documents, and determine necessary action.

17.0	General hydraulic system diagnosis and repair.
18.0	Diagnose and repair hydraulic pumps.
19.0	Diagnose and repair hydraulic filtration/reservoirs (tanks).
20.0	Diagnose and repair hydraulic hoses, fittings, and connections.
21.0	Diagnose and repair hydraulic control valves.
22.0	Diagnose and repair hydraulic actuators.

2015 - 2016
Florida Department of Education
Student Performance Standards

Course Number:  DIM0103
Occupational Completion Point:  A
Diesel Engine Preventative Maintenance Technician – 150 Hours – SOC Code 49-3031

Course Description: 
The Diesel Engine Preventative Maintenance Technician course prepares students for entry into the Diesel Engine Service industry. Content emphasizes beginning skills and concepts as a recommended requisite. Students study engine system, cab and hood systems, electrical/electronic systems, frame and chassis systems diagnostics, service, and repair.

CTE Standards and Benchmarks	Priority Number	
01.0	Diagnose and repair engine systems		
01.01	Engine--The student will be able to: 		
01.01.1	Check engine starting/operation (including unusual noises, vibrations, exhaust smoke, etc.); record idle and governed.	P-1	
01.01.2	Inspect vibration damper.	P-1	
01.01.3	Inspect belts, tensioners, and pulleys; check and adjust belt tension; check belt alignment.	P-1	
01.01.4	Check engine oil level; check engine for oil, coolant, and fuel leaks (Engine Off).	P-1	
01.01.5	Inspect engine mounts for looseness and deterioration.	P-1	
01.01.6	Check engine for oil, coolant, air, fuel and exhaust leaks (Engine Running).	P-1	
01.01.7	Check electrical wiring, routing, and hold-down clamps, including Engine Control Module/Powertrain Control Module (ECM/PCM).	P-1	
01.02	Fuel system--The student will be able to:		
01.02.1	Check fuel tanks, mountings, lines, caps, and vents.	P-1	
01.02.2	Inspect throttle linkages and return springs.	P-1	
01.02.3	Drain water from fuel system.	P-1	
01.02.4	Inspect water separator/fuel heater; replace fuel filter(s); prime and bleed fuel system.	P-1	
01.03	Air induction and exhaust system--The student will be able to:		
01.03.1	Check exhaust system mountings for looseness and damage.	P-1	
01.03.2	Check engine exhaust system for leaks, proper routing, and damaged or missing components to include exhaust gas recirculation (EGR) system if equipped.	P-1	
01.03.3	Check air induction system: piping, charge air cooler, hoses, clamps, and mountings; check for air restrictions and leaks.	P-1	
01.03.4	Inspect turbocharger for leaks; check mountings and connections.	P-1	
01.03.5	Check operation of engine compression/exhaust brake.	P-1	
01.03.6	Service or replace air filter as needed; check and reset air filter restriction indicator.	P-1	
01.04	Cooling system--The student will be able to:		
01.04.1	Check operation of fan clutch.	P-1	
01.04.2	Inspect radiator (including air flow restriction, leaks, and damage) and mountings.	P-1	
01.04.3	Inspect fan assembly and shroud.	P-1	
01.04.4	Pressure test cooling system and radiator cap.	P-1	
01.04.5	Inspect coolant hoses and clamps.	P-1	
01.04.6	Inspect coolant recovery system.	P-1	
01.04.7	Check coolant for contamination, supplemental coolant additives (SCA) concentration, and protection level (freeze point).	P-1	
01.04.8	Service coolant filter/conditioner.	P-1	
01.04.9	Inspect water pump for leaks and bearing play.	P-1	
01.05	Lubrication system--The student will be able to:		
01.05.1	Change engine oil and filters; visually check oil for coolant or fuel contamination; inspect and clean magnetic drain plugs.	P-1	
01.05.2	Take an engine oil sample.	P-1	
02.0	Diagnose and repair cab and hood systems		
02.01	Instruments and controls--The student will be able to:		
02.01.1	Inspect key condition and operation of ignition switch.	P-1	
02.01.2	Check warning indicators.	P-1	
02.01.3	Check instruments; record oil pressure and system voltage.	P-1	
02.01.4	Check mechanical, electronic, and emergency shut down operation.	P-1	
02.01.5	Check mechanical and electronic engine speed controls.	P-1	
02.01.6	Check heater, ventilation, and air conditioning (HVAC) controls.	P-1	
02.01.7	Check operation of all accessories.	P-1	
02.01.8	Using diagnostic tool or on-board diagnostic system; extract engine monitoring information.	P-1	
02.02	Safety equipment--The student will be able to:		
02.02.1	Check operation of electric/air horns and back-up warning devices.	P-1	
02.02.2	Check condition and documentation of safety flares, spare fuses, triangles, fire extinguisher, and all required decals.	P-1	
02.02.3	Inspect seat belts and sleeper restraints.	P-1	
02.02.4	Inspect wiper blades and arms.	P-1	
02.03	Hardware--The student will be able to:		
02.03.1	Check wiper and washer operation.	P-1	
02.03.2	Inspect windshield glass for cracks or discoloration; check sun visor.	P-1	
02.03.3	Check seat condition, operation, and mounting.	P-1	
02.03.4	Check door glass and window operation.	P-1	
02.03.5	Inspect steps and grab handles.	P-1	
02.03.6	Inspect mirrors, mountings, brackets, and glass.	P-1	
02.03.7	Record all observed physical damage.	P-1	
02.03.8	Lubricate all cab and hood grease fittings.	P-1	
02.03.9	Inspect and lubricate door and hood hinges, latches, strikers, lock cylinders, safety latches, linkages, and cables.	P-1	
02.03.10	Inspect cab mountings, hinges, latches, linkages and ride height; service as needed.	P-1	
02.03.11	Inspect tilt cab hydraulic pump, lines, and cylinders for leakage; inspect safety devices; service as needed.	P-1	
02.04	Heating, ventilation, and air conditioning (HVAC)--The student will be able to:		
02.04.1	Inspect A/C condenser and lines for condition and visible leaks; check mountings.	P-1	
02.04.2	Inspect A/C compressor and lines for condition and visible leaks; check mountings.	P-1	
02.04.3	Check A/C system condition and operation; check A/C monitoring system, if applicable.	P-1	
02.04.4	Check HVAC air inlet filters and ducts; service as needed.	P-1	
03.0	Diagnose and repair electrical/electronic systems		
03.01	Battery and starting systems--The student will be able to:		
03.01.1	Inspect battery box(es), cover(s), and mountings.	P-1	
03.01.2	Inspect battery hold-downs, connections, cables, and cable routing; service as needed.	P-1	
03.01.3	Check/record battery state-of-charge (open circuit voltage) and condition.	P-1	
03.01.4	Perform battery test (load and/or capacitance).	P-1	
03.01.5	Inspect starter, mounting, and connections.	P-1	
03.01.6	Engage starter; check for unusual noises, starter drag, and starting difficulty.	P-1	
03.02	Charging system--The student will be able to:		
03.02.1	Inspect alternator, mountings, wiring and wiring routing; determine needed action.	P-1	
03.02.2	Perform alternator current output test.	P-1	
03.02.3	Perform alternator voltage output test.	P-1	
03.03	Lighting system--The student will be able to:		
03.03.1	Check operation of interior lights; determine needed action.	P-1	
03.03.2	Check all exterior lights, lenses, reflectors, and conspicuity tape; check headlight alignment; determine needed action.	P-1	
03.03.3	Inspect and test tractor-to-trailer multi-wire connector(s), cable(s), and holder(s); determine needed action.	P-1	
04.0	Diagnose and repair frame and chassis systems		
04.01	Air brakes--The student will be able to:		
04.01.1	Check parking brake operation.	P-1	
04.01.2	Record air governor cut-out setting (psi).	P-1	
04.01.3	Check air drier drain valve operation.	P-1	
04.01.4	Check air system for leaks (brakes released).	P-1	
04.01.5	Check air system for leaks (brakes applied).	P-1	
04.01.6	Test one-way and double-check valves.	P-1	
04.01.7	Check low air pressure warning devices.	P-1	
04.01.8	Check air governor cut-in pressure.	P-1	
04.01.9	Check emergency (spring) brake control/modulator valve, if applicable.	P-1	
04.01.10	Check tractor protection valve.	P-1	
04.01.11	Test air pressure build-up time.	P-1	
04.01.12	Inspect coupling air lines, holders, and gladhands.	P-1	
04.01.13	Check brake chambers and air lines for secure mounting and damage.	P-1	
04.01.14	Service air drier.	P-1	
04.01.15	Inspect and record brake lining/pad condition, thickness, and contamination.	P-1	
04.01.16	Inspect and record condition of brake drums/rotors.	P-1	
04.01.17	Check operation of brake manual slack adjusters; adjust as needed.	P-1	
04.01.18	Check operation and adjustment of brake automatic slack adjusters.	P-1	
04.01.19	Lubricate all brake component grease fittings.	P-1	
04.01.20	Check condition and operation of hand brake (trailer) control valve.	P-1	
04.01.21	Perform antilock brake system (ABS) operational system self-test.	P-1	
04.01.22	Drain air tanks and check for contamination.	P-1	
04.01.23	Check condition of pressure relief (safety) valves.	P-1	
04.02	Hydraulic brakes--The student will be able to:		
04.02.1	Check master cylinder fluid level and condition.	P-1	
04.02.2	Inspect brake lines, fittings, flexible hoses, and valves for leaks and damage.	P-1	
04.02.3	Check parking brake operation; inspect parking brake application and holding devices; adjust as needed.	P-1	
04.02.4	Check operation of hydraulic system: pedal travel, pedal effort, pedal feel (drift).	P-1	
04.02.5	Inspect wheel cylinders/calipers for leakage and damage.	P-1	
04.02.6	Inspect power brake booster(s), hoses; and check/control valves; check power brake booster, reservoir fluid level and condition.	P-1	
04.02.7	Inspect and record brake lining/pad condition and thickness, and contamination.	P-1	
04.02.8	Inspect and record condition of brake drums/rotors.	P-1	
04.02.9	Adjust drum brakes.	P-1	
04.03	Drivetrain--The student will be able to:		
04.03.1	Check operation of clutch, clutch brake, and gearshift.	P-1	
04.03.2	Check clutch linkage/cable for looseness or binding, if applicable.	P-1	
04.03.3	Check hydraulic clutch slave and master cylinders, lines, fittings, and hoses, if applicable.	P-1	
04.03.4	Check clutch adjustment; adjust as needed.	P-1	
04.03.5	Check transmission case, seals, filter, hoses, and cooler for cracks and leaks.	P-1	
04.03.6	Inspect transmission breather.	P-1	
04.03.7	Inspect transmission mounts.	P-1	
04.03.8	Check transmission oil level, type, and condition.	P-1	
04.03.9	Inspect U-joints, yokes, drive lines, and center bearings for looseness, damage, and proper phasing.	P-1	
04.03.10	Inspect axle housing(s) for cracks and leaks.	P-1	
04.03.11	Inspect axle breather(s).	P-1	
04.03.12	Lubricate all drivetrain grease fittings.	P-1	
04.03.13	Check drive axle(s) oil level, type, and condition.	P-1	
04.03.14	Change drive axle(s) oil and filter; check and clean magnetic plugs.	P-1	
04.03.15	Check two-speed axle unit operation and oil level.	P-1	
04.03.16	Change transmission oil and filter; check and clean magnetic plugs.	P-1	
04.03.17	Check interaxle differential lock operation.	P-1	
04.03.18	Check range shift operation.	P-1	
04.04	Suspension and steering systems--The student will be able to:		
04.04.1	Check steering wheel operation for free play or binding.	P-1	
04.04.2	Check power steering pump, mounting, and hoses for leaks, condition, and routing; check fluid level.	P-1	
04.04.3	Change power steering fluid and filter.	P-1	
04.04.4	Inspect steering gear for leaks and secure mounting.	P-1	
04.04.5	Inspect steering shaft U-joints, pinch bolts, splines, pitman arm-to-steering sector shaft, tie rod ends, linkage, and linkage-assist power steering cylinders.	P-1	
04.04.6	Check king pin wear.	P-1	
04.04.7	Check wheel bearings for looseness and noise.	P-1	
04.04.8	Check oil level and condition in all non-drive hubs; check for leaks.	P-1	
04.04.9	Remove and inspect wheel bearings; reassemble and adjust.	P-1	
04.04.10	Inspect springs, hangers, shackles, spring U-bolts, and insulators.	P-1	
04.04.11	Inspect shock absorbers for leaks and secure mounting.	P-1	
04.04.12	Inspect air suspension springs, mounts, hoses, valves, linkage, and fittings for leaks and damage.	P-1	
04.04.13	Check and record suspension ride height.	P-1	
04.04.14	Lubricate all suspension and steering grease fittings.	P-1	
04.04.15	Check toe adjustment.	P-1	
04.04.16	Check tandem axle alignment and spacing.	P-1	
04.04.17	Check axle locating components (radius, torque, and/or track rods).	P-1	
04.05	Tires and wheels--The student will be able to: 		
04.05.1	Inspect tires for irregular wear patterns and proper mounting of directional tires.	P-1	
04.05.2	Inspect tires for cuts, cracks, bulges, and sidewall damage.	P-1	
04.05.3	Inspect valve caps and stems; replace as needed.	P-1	
04.05.4	Measure and record tread depth; probe for imbedded debris.	P-1	
04.05.5	Check and record air pressure; adjust air pressure in accordance with manufacturers’ specifications.	P-1	
04.05.6	Check for loose lugs and/or slipped wheels; check mounting hardware condition; service as needed.	P-1	
04.05.7	Retorque lugs in accordance with manufacturer's specifications.	P-1	
04.05.8	Inspect wheels and spacers for cracks or damage.	P-1	
04.05.9	Check tire matching (diameter and tread) on dual tire installations.	P-1	
04.06	Frame and fifth wheel--The student will be able to:		
04.06.1	Inspect fifth wheel mounting bolts, air lines, and locks.	P-1	
04.06.2	Test operation of fifth wheel locking device; adjust if necessary.	P-1	
04.06.3	Check mud flaps and brackets.	P-1	
04.06.4	Check pintle hook assembly and mounting.	P-1	
04.06.5	Lubricate all fifth wheel grease fittings and plate.	P-1	
04.06.6	Inspect frame and frame members for cracks and damage.	P-1	

2015 - 2016
Florida Department of Education
Student Performance Standards

Course Number:  DIM0106
Occupational Completion Point:  B
Diesel Heating and Air Conditioning Technician – 150 Hours – SOC Code 49-3031

Course Description: 
The Diesel Heating and Air Conditioning Technician course prepares students for entry into the Diesel Engine Service industry. Content emphasizes beginning skills and concepts as a recommended requisite. Students study diagnostic, service, and repair of HVAC, and A/C systems.

CTE Standards and Benchmarks	Priority Number	
05.0	HVAC systems diagnosis, service, and repair--The student will be able to:		
05.01	Verify the need for service or repair of HVAC systems based on unusual operating noises; determine needed action.	P-1	
05.02	Verify the need of service or repair of HVAC systems based on unusual visual, smell, and touch conditions; determine needed action.	P-1	
05.03	Identify system type and components (cycling clutch orifice tube - CCOT, expansion valve) and conduct performance test(s) on HVAC systems; determine needed action.	P-1	
06.0	A/C system and component diagnosis, service, and repair		
06.01	A/C system - general--The student will be able to: 		
06.01.1	Diagnose the cause of temperature control problems in the A/C system; determine needed action.	P-1	
06.01.2	Identify refrigerant type and check for contamination; determine needed action.	P-2	
06.01.3	Diagnose A/C system problems indicated by pressure gauge and temperature readings; determine needed action.	P-1	
06.01.4	Diagnose A/C system problems indicated by visual, audible, smell, and touch procedures; determine needed action.	P-1	
06.01.5	Perform A/C system leak test; determine needed action.	P-1	
06.01.6	Evacuate A/C system using appropriate equipment.	P-1	
06.01.7	Internally clean contaminated A/C system components and hoses.	P-2	
06.01.8	Charge A/C system with refrigerant.	P-1	
06.01.9	Identify lubricant type needed for system application.	P-1	
06.02	Compressor and clutch--The student will be able to:		
06.02.1	Diagnose A/C system problems that cause protection devices (pressure, thermal, and electronic) to interrupt system operation; determine needed action.	P-1	
06.02.2	Inspect, test, and replace A/C system pressure, thermal, and electronic protection devices.	P-2	
06.02.3	Inspect, and replace A/C compressor drive belts, pulleys, and tensioners; adjust belt tension and check alignment.	P-1	
06.02.4	Inspect, test, service, and replace A/C compressor clutch components or assembly.	P-3	
06.02.5	Inspect and correct A/C compressor lubricant level (if applicable).	P-2	
06.02.6	Inspect, test, and replace A/C compressor.	P-2	
06.02.7	Inspect, repair, or replace A/C compressor mountings and hardware.	P-2	
06.03	Evaporator, condenser, and related components--The student will be able to:		
06.03.1	Correct system lubricant level when replacing the evaporator, condenser, receiver/drier or accumulator/drier, and hoses.	P-1	
06.03.2	Inspect A/C system hoses, lines, filters, fittings, and seals; determine needed action.	P-1	
06.03.3	Inspect A/C condenser for proper air flow.	P-1	
06.03.4	Inspect and test A/C system condenser and mountings; determine needed action.	P-2	
06.03.5	Inspect and replace receiver/drier or accumulator/drier.	P-1	
06.03.6	Inspect and test cab/sleeper refrigerant solenoid, expansion valve(s); check placement of thermal bulb (capillary tube); determine needed action.	P-3	
06.03.7	Inspect and replace orifice tube.	P-1	
06.03.8	Inspect and test cab/sleeper evaporator core; determine needed action.	P-3	
06.03.9	Inspect, clean, and repair evaporator housing and water drain; inspect and service/replace evaporator air filter.	P-1	
06.03.10	Identify and inspect A/C system service ports (gauge connections); determine needed action.	P-1	
06.03.11	Diagnose system failures resulting in refrigerant loss from the A/C system high pressure relief device; determine needed action.	P-2	
06.04	Heating and engine cooling systems diagnosis, service, and repair--The student will be able to:		
06.04.1	Diagnose the cause of outlet air temperature control problems in the HVAC system; determine needed action.	P-1	
06.04.2	Diagnose window fogging problems; determine needed action.	P-1	
06.04.3	Perform engine cooling system tests for leaks, protection level, contamination, coolant level, coolant type, temperature, and conditioner concentration; determine needed action.	P-2	
06.04.4	Inspect engine cooling and heating system hoses, lines, and clamps; determine needed action.	P-1	
06.04.5	Inspect and test radiator, pressure cap, and coolant recovery system (surge tank); determine needed action.	P-1	
06.04.6	Inspect water pump for leaks and bearing play; determine needed action.	P-2	
06.04.7	Inspect and test thermostats, by-passes, housings, and seals; determine needed repairs.	P-2	
06.04.8	Recover, flush and refill with recommended coolant/additive package; bleed cooling system.	P-1	
06.04.9	Inspect thermostatic cooling fan system (hydraulic, pneumatic, and electronic) and fan shroud; replace as needed.	P-2	
06.04.10	Inspect and test heating system coolant control valve(s) and manual shut-off valves; determine needed action.	P-2	
06.04.11	Inspect and flush heater core; determine needed action.	P-2	
07.0	Operating systems and related controls diagnosis and repair		
07.01	Electrical--The student will be able to:		
07.01.1	Diagnose the cause of failures in HVAC electrical control systems; determine needed action.	P-1	
07.01.2	Inspect and test A/C heater blower motors, resistors, switches, relays, modules, wiring, and protection devices; determine needed action.	P-2	
07.01.3	Inspect and test A/C compressor clutch relays, modules, wiring, sensors, switches, diodes, and protection devices; determine needed action.	P-2	
07.01.4	Inspect and test A/C-related electronic engine control systems; determine needed action.	P-2	
07.01.5	Inspect and test engine cooling/condenser fan motors, relays, modules, switches, sensors wiring, and protection devices; determine needed action.	P-2	
07.01.6	Inspect and test electric actuator motors, relays/modules, switches, sensors, wiring, and protection devices; determine needed action.	P-3	
07.01.7	Inspect and test HVAC system electrical control panel assemblies; determine needed action.	P-3	
07.02	Air/vacuum/mechanical--The student will be able to:		
07.02.1	Diagnose the cause of failures in HVAC air, vacuum, and mechanical switches and controls; determine needed action.	P-1	
07.02.2	Inspect and test HVAC system air/vacuum/mechanical control panel assemblies; determine needed action.	P-3	
07.02.3	Inspect, test, and adjust HVAC system air/vacuum/mechanical control cables and linkages; determine needed action.	P-3	
07.02.4	Inspect and test HVAC system vacuum actuators (diaphragms/motors) and hoses; determine needed action.	P-3	
07.02.5	Inspect and test HVAC system vacuum reservoir(s), check valve(s), and restrictors; determine needed action.	P-3	
07.02.6	Inspect, test, and adjust HVAC system ducts, doors, and outlets; determine needed action.	P-3	
NOTE: Tasks 1 through 5 should be accomplished in accordance with published EPA and appropriate SAE "J" standards for R-12, 
            R-134a, and EPA approved refrigerant blends.	
07.03	Refrigerant recovery, recycling, and handling--The student will be able to:		
07.03.1	Maintain and verify correct operation of certified equipment.	P-1	
07.03.2	Identify (by label application or use of a refrigerant identifier) and recover A/C system refrigerant.	P-1	
07.03.3	Recycle refrigerant.	P-1	
07.03.4	Handle, label, and store refrigerant.	P-1	
07.03.5	Test recycled refrigerant for non-condensable gases.	P-1	

2015 - 2016
Florida Department of Education
Student Performance Standards

Course Number:  DIM0107
Occupational Completion Point:  C
Diesel Steering and Suspension Technician – 150 Hours – SOC Code 49-3031

Course Description: 
The Diesel Steering and Suspension Technician course prepares students for entry into the Diesel Engine Service industry. Content emphasizes beginning skills and concepts as a recommended requisite. Students study diagnostic, service, and repair of steering, suspension, wheel alignment, wheels, tires, and frame systems.

CTE Standards and Benchmarks	Priority Number	
08.0	Steering systems diagnosis and repair 		
08.01	Steering column--The student will be able to:		
08.01.1	Diagnose fixed and driver adjustable steering column and shaft noise, looseness, and binding problems; determine needed action.	P-1	
08.01.2	Inspect steering shaft U-joint(s), slip joints, bearings, bushings, and seals; phase shaft U-joints; determine needed action.	P-1	
08.01.3	Check and adjust cab mounting and ride height.	P-3	
08.01.4	Center the steering wheel as needed.	P-1	
08.01.5	Disable and enable supplemental restraint system (SRS) in accordance with manufacturers’ procedures.	P-1	
08.02	Steering units--The student will be able to:		
08.02.1	Diagnose power steering system noise, steering binding, darting/oversteer, reduced wheel cut, steering wheel kick, pulling, non-recovery, turning effort, looseness, hard steering, overheating, fluid leakage, and fluid aeration problems; determine needed action.	P-1	
08.02.2	Determine recommended type of power steering fluid; check level and condition; determine needed action.	P-1	
08.02.3	Flush and refill power steering system; purge air from system.	P-2	
08.02.4	Perform power steering system pressure, temperature, and flow tests; determine needed action.	P-2	
08.02.5	Inspect, service, or replace power steering reservoir including filter, seals, and gaskets.	P-2	
08.02.6	Inspect, and reinstall/replace pulleys, tensioners, and drive belts; adjust drive belts and check alignment.	P-1	
08.02.7	Inspect, replace as required, power steering pump drive gear and coupling.	P-3	
08.02.8	Inspect, adjust, or replace power steering pump, mountings, and brackets.	P-3	
08.02.9	Inspect and replace power steering system cooler, lines, hoses, clamps/mountings, hose routings, and fittings.	P-3	
08.02.10	Inspect, adjust, or replace linkage-assist type power steering cylinder or gear (dual system).	P-3	
08.02.11	Inspect, adjust, repair, or replace integral type power steering gear and mountings.	P-1	
08.02.12	Adjust manual and automatic steering gear poppet/relief valves.	P-2	
08.03	Steering linkage--The student will be able to:		
08.03.1	Inspect and align pitman arm; replace as needed.	P-1	
08.03.2	Inspect drag link (relay rod) and tie rod ends; adjust or replace as needed.	P-1	
08.03.3	Inspect steering arm and levers, and linkage pivot joints; replace as needed.	P-1	
08.03.4	Inspect clamps and retainers on cross tube/relay rod/centerline/tie rod; position or replace as needed.	P-1	
08.03.5	Check and adjust wheel stops.	P-1	
08.03.6	Lubricate steering linkage joints as needed.	P-1	
09.0	Suspension systems diagnosis and repair--The student will be able to:		
09.01	Inspect front axles, U-bolts, and nuts; determine needed action.	P-1	
09.02	Inspect and service king pin, steering knuckle bushings, locks, bearings, seals, and covers; determine needed action.	P-1	
09.03	Inspect shock absorbers, bushings, brackets, and mounts; replace as needed.	P-1	
09.04	Inspect leaf springs, center bolts, clips, eye bolts and bushings, shackles, slippers, insulators, brackets, and mounts; determine needed action.	P-1	
09.05	Inspect torque arms, bushings, and mounts; determine needed action.	P-1	
09.06	Inspect axle aligning devices such as radius rods, track bars, stabilizer bars, and related bushings, mounts, shims, and cams; determine needed action.	P-1	
09.07	Inspect walking beams, center (cross) tube, bushings, mounts, load pads, and saddles/caps; replace as needed.	P-3	
09.08	Inspect and test air suspension pressure regulator and height control valves, lines, hoses, dump valves, and fittings; adjust, repair or replace as needed.	P-1	
09.09	Inspect and test air springs, mounting plates, springs, suspension arms, and bushings; replace as needed.	P-1	
09.10	Measure vehicle ride height; determine needed action.	P-1	
09.11	Diagnose rough ride problems; determine needed action.	P-3	
10.0	Wheel alignment diagnosis, adjustment, and repair--The student will be able to:		
10.01	Diagnose vehicle wandering, pulling, shimmy, hard steering and off-center steering wheel problem(s); adjust and repair as needed.	P-1	
10.02	Check camber; determine needed action.	P-2	
10.03	Check caster; adjust as needed.	P-2	
10.04	Check toe; adjust as needed.	P-1	
10.05	Check rear axle(s) alignment (thrust line/centerline) and tracking; adjust or repair as needed.	P-2	
10.06	Diagnose turning/Ackerman angle (toe-out-on-turns) problems; determine needed action.	P-3	
10.07	Check front axle alignment (centerline); adjust or repair as needed.	P-2	
11.0	Wheels and tires diagnosis and repair--The student will be able to:		
11.01	Diagnose unusual tire wear patterns, check tread depth, mismatched tread design; determine needed action.	P-1	
11.02	Diagnose wheel/tire vibration, shimmy, pounding, hop (tramp) problems; determine needed action.	P-2	
12.0	Frame service and repair--The student will be able to:	P-1	
12.01	Inspect and adjust fifth wheel, pivot pins, bushings, locking jaw mechanisms, and mounting bolts; determine needed action.	P-1	
12.02	Inspect sliding fifth wheel, tracks, stops, locking systems, air cylinders, springs, lines, hoses, and controls.	P-1	
12.03	Inspect frame and frame members for cracks, breaks, corrosion, distortion, elongated holes, looseness, and damage; determine needed repairs.	P-1	
12.04	Inspect, install, or repair frame hangers, brackets, and crossmembers in accordance with manufacturers’ recommended procedures.	P-3	
12.05	Inspect, repair or replace pintle hooks and draw bars.	P-1	

2015 - 2016
Florida Department of Education
Student Performance Standards

Course Number:  DIM0108
Occupational Completion Point:  D
Diesel Drivetrain Technician – 150 Hours – SOC Code 49-3031

Course Description: 
The Diesel Drivetrain Technician course prepares students for entry into the Diesel Engine Service industry. Content emphasizes beginning skills and concepts as a recommended requisite. Students study diagnostic, service, and repair of clutch, transmission, driveshaft, universal joint, and drive axle systems.

The first task in Drivetrain is to listen to and verify the operator's concern, review past maintenance and repair documents, and determine necessary action.

CTE Standards and Benchmarks	Priority Number	
13.0	Clutch diagnosis and repair--The student will be able to:		
13.01	Diagnose clutch noise, binding, slippage, pulsation, vibration, grabbing, dragging, and chatter problems; determine needed action.	P-1	
13.02	Inspect and adjust clutch linkage, cables, levers, brackets, bushings, pivots, springs, and clutch safety switch (includes push and pull-type assemblies); check pedal height and travel; perform needed action.	P-1	
13.03	Inspect, adjust, repair, or replace hydraulic clutch slave and master cylinders, lines, and hoses; bleed system.	P-2	
13.04	Inspect, adjust, lubricate or replace release (throw-out) bearing, sleeve, bushings, springs, housing, levers, release fork, fork pads, rollers, shafts, and seals.	P-1	
13.05	Inspect, adjust, and replace single-disc clutch pressure plate and clutch disc.	P-2	
13.06	Inspect, adjust, and replace two-plate clutch pressure plate, clutch discs, intermediate plate, and drive pins/lugs.	P-1	
13.07	Inspect and/or replace clutch brake assembly; inspect input shaft and bearing retainer; perform needed action.	P-1	
13.08	Inspect, adjust, and replace self-adjusting/continuous-adjusting clutch mechanisms.	P-2	
13.09	Inspect and replace pilot bearing.	P-1	
13.10	Inspect flywheel mounting area on crankshaft, rear main oil seal, and measure crankshaft end play; determine needed action.	P-1	
13.11	Inspect flywheel, starter ring gear and measure flywheel face and pilot bore runout; determine needed action.	P-1	
13.12	Inspect flywheel housing(s) to transmission housing/engine mating surface(s) and measure flywheel housing face and bore runout; determine needed action.	P-1	
14.0	Transmission diagnosis and repair--The student will be able to:		
14.01	Diagnose transmission noise, shifting, lockup, jumping-out-of-gear, overheating, and vibration problems; determine needed action.	P-1	
14.02	Diagnose transmission component failure cause, both before and during disassembly procedures; determine needed action.	P-2	
14.03	Inspect, adjust, service, repair, or replace transmission remote shift linkages, brackets, bushings, pivots, and levers.	P-2	
14.04	Inspect, test, repair, or replace air shift controls, lines, hoses, valves, regulators, filters, and cylinder assemblies.	P-1	
14.05	Inspect and replace transmission mounts, insulators, and mounting bolts; determine needed action.	P-3	
14.06	Inspect for leakage and replace transmission cover plates, gaskets, seals, and cap bolts; inspect seal surfaces and vents; repair as needed.	P-1	
14.07	Check transmission fluid level and condition; determine needed service; add proper type of lubricant.	P-1	
14.08	Inspect, adjust, and replace transmission shift lever, cover, rails, forks, levers, bushings, sleeves, detents, interlocks, springs, and lock bolts/safety wires.	P-2	
14.09	Remove and reinstall transmission.	P-1	
14.10	Inspect input shaft, gear, spacers, bearings, retainers, and slingers; replace as needed.	P-3	
14.11	Inspect and adjust main shaft, gears, sliding clutches, washers, spacers, bushings, bearings, auxiliary drive assemblies, retainers, and keys; replace as needed.	P-3	
14.12	Inspect countershafts, gears, bearings, retainers, and keys; adjust bearing preload and time multiple countershaft gears; replace as needed.	P-3	
14.13	Inspect output shafts, gears, washers, spacers, bearings, retainers, and keys; replace as needed.	P-3	
14.14	Inspect and/or replace reverse idler shafts, gears, bushings, bearings, thrust washers, and retainers; check reverse idler gear end play (where applicable).	P-3	
14.15	Inspect synchronizer hub, sleeve, keys (inserts), springs, blocking rings, synchronizer plates, blocker pins, and sliding clutches; replace as needed.	P-3	
14.16	Inspect transmission cases including surfaces, bores, bushings, pins, studs, and magnets; replace as needed.	P-3	
14.17	Inspect transmission lubrication system pumps, troughs, collectors, and slingers; service or replace as needed.	P-3	
14.18	Inspect transmission oil filters and coolers; replace as needed.	P-2	
14.19	Inspect mechanical and electronic speedometer components; determine needed action.	P-2	
14.20	Inspect and adjust power take-off (PTO) assemblies, controls, and shafts; perform needed action.	P-3	
14.21	Inspect and test function of backup light, neutral start, and warning device circuits; repair as needed.	P-1	
14.22	Inspect and test transmission temperature gauge sending unit/sensor; determine needed action.	P-2	
14.23	Inspect, test operation, adjust, repair, or replace automated mechanical transmission and manual electronic shift controls, shift, range and splitter solenoids, shift motors, indicators, speed and range sensors, electronic/transmission control units (ECU/TCU), neutral/in gear and reverse switches, and wiring harnesses.	P-2	
14.24	Inspect, test operation, repair, or replace automated mechanical transmission electronic shift selectors, air and electrical switches, displays and indicators, wiring harnesses, and air lines.	P-2	
14.25	Use appropriate diagnostic tools and procedures to diagnose automated mechanical transmission problems; check and record diagnostic codes, clear codes, and interpret digital multimeter (DMM) readings; determine needed repairs.	P-2	
14.26	Inspect, test operation, adjust, repair, or replace automatic transmission electronic and manual shift controls, shift solenoids, shift motors, indicators, speed and range sensors, electronic/transmission control units (ECU/TCE) neutral/in gear and reverse switches and wiring harnesses.	P-3	
14.27	Inspect, test operation, repair, or replace automated mechanical transmission electronic shift selectors, switches, displays and indicators, wiring harnesses.	P-2	
14.28	Use appropriate diagnostic tools and procedures to diagnose automated transmission problems; check and record diagnostic codes, clear codes, and interpret digital multimeter (DMM) readings; determine needed repairs.	P-2	
15.0	Driveshaft and universal joint diagnosis and repair--The student will be able to:		
15.01	Diagnose driveshaft and universal joint noise and vibration problems; determine needed action.	P-1	
15.02	Inspect, service, or replace driveshaft, slip joints, yokes, drive flanges, and universal joints; check phasing of all yokes.	P-1	
15.03	Inspect and replace driveshaft center support bearings and mounts; determine needed action.	P-1	
15.04	Measure and adjust drive line angles.	P-1	
16.0	Drive axle diagnosis and repair--The student will be able to:		
16.01	Diagnose drive axle(s) drive unit noise and overheating problems; determine needed action.	P-2	
16.02	Check and repair fluid leaks; inspect and replace drive axle housing cover plates, gaskets, sealants, vents, magnetic plugs, and seals.	P-1	
16.03	Check drive axle fluid level and condition; determine needed service; add proper type of lubricant.	P-1	
16.04	Remove and replace differential carrier assembly.	P-2	
16.05	Inspect and replace differential case assembly including spider gears, cross shaft, side gears, thrust washers, case halves, and bearings.	P-3	
16.06	Inspect and replace components of locking differential case assembly.	P-3	
16.07	Inspect differential carrier case and caps, side bearing bores, and pilot (spigot, pocket) bearing bore; determine needed action.	P-3	
16.08	Measure ring gear runout; determine needed action.	P-3	
16.09	Inspect and replace ring and drive pinion gears, spacers, sleeves, bearing cages, and bearings.	P-3	
16.10	Measure and adjust drive pinion bearing preload.	P-3	
16.11	Measure and adjust drive pinion depth.	P-3	
16.12	Measure and adjust side bearing preload and ring gear backlash.	P-3	
16.13	Check and interpret ring gear and pinion tooth contact pattern; determine needed action.	P-3	
16.14	Inspect, adjust, or replace ring gear thrust block/bolt.	P-3	
16.15	Inspect, adjust, repair, or replace planetary gear-type 2-speed axle assembly including: case, idler pinion, pins, thrust washers, sliding clutch gear, shift fork, pivot, seals, cover, and springs.	P-3	
16.16	Inspect, repair, or replace 2-speed axle shift control system, speedometer adapters, motors, axle shift units, wires, air lines, and connectors.	P-3	
16.17	Inspect power divider (inter-axle differential) assembly; determine needed action.	P-3	
16.18	Inspect, adjust, repair, or replace air operated power divider (inter-axle differential) lockout assembly including diaphragms, seals, springs, yokes, pins, lines, hoses, fittings, and controls.	P-2	
16.19	Inspect, repair, or replace drive axle lubrication system: pump, troughs, collectors, slingers, tubes, and filters.	P-3	
16.20	Inspect and replace drive axle shafts.	P-1	
16.21	Remove and replace wheel assembly; check rear wheel seal and axle flange gasket for leaks; perform needed action.	P-1	
16.22	Diagnose drive axle for wheel bearing noise and damage; perform needed action.	P-1	
16.23	Inspect and test drive axle temperature gauge sending unit/sensor; determine needed action.	P-2	
16.24	Clean, inspect, lubricate and replace wheel bearings; replace seals and wear rings; adjust drive axle wheel bearings.	P-1	

2015 - 2016
Florida Department of Education
Student Performance Standards

Course Number:  DIM0109
Occupational Completion Point:  E
Diesel Hydraulics Technician – 150 Hours – SOC Code 49-3031

Course Description: 
The Diesel Hydraulics Technician course prepares students for entry into the Diesel Engine Service industry. Content emphasizes beginning skills and concepts as a recommended requisite. Students study diagnostic, service, and repair of hydraulic, pumps, filtration/reservoir, hoses, fittings, connectors, control valves, and actuator systems.

For every task in Hydraulics, the following safety task must be strictly enforced:

Comply with personal and environmental safety practices associated with clothing; eye protection; hand protection; proper lifting practices; hand tools; power equipment; proper ventilation; and the handling, storage, and disposal of fuels/chemicals/materials in accordance with federal, state, and local regulations.

The first task in Hydraulics is to listen to and verify the operator’s concern, review past maintenance and repair documents, and determine necessary action.

CTE Standards and Benchmarks	Priority Number	
17.0	General hydraulic system diagnosis and repair--The student will be able to:		
17.01	Identify system type (closed and open) and verify proper operation.	P-1	
17.02	Read and interpret system diagrams and schematics.	P-1	
17.03	Perform system temperature, pressure, flow, and cycle time tests; determine needed action.	P-1	
17.04	Verify placement of equipment /component safety labels and placards; determine needed action.	P-1	
18.0	Diagnose and repair hydraulic pumps--The student will be able to:		
18.01	Identify system fluid type.	P-1	
18.02	Identify causes of pump failure, unusual pump noises, and temperature, flow, and leakage problems; determine needed action.	P-2	
18.03	Determine pump type, rotation, and drive system.	P-2	
18.04	Remove and install pump; prime and/or bleed system.	P-2	
18.05	Inspect pump inlet for restrictions and leaks; determine needed action.	P-2	
18.06	Inspect pump outlet for restrictions and leaks; determine needed action.	P-2	
19.0	Diagnose and repair hydraulic filtration/reservoirs (tanks)--The student will be able to:		
19.01	Identify type of filtration system; verify filter application and flow direction.	P-1	
19.02	Service filters and breathers.	P-1	
19.03	Identify causes of system contamination; determine needed action.	P-2	
19.04	Take a hydraulic oil sample.	P-2	
19.05	Check reservoir fluid level and condition; determine needed action.	P-1	
19.06	Inspect and repair or replace reservoir, sight glass, vents, caps, mounts, valves, screens, supply and return lines.	P-2	
20.0	Diagnose and repair hydraulic hoses, fittings, and connections--The student will be able to:		
20.01	Diagnose causes of component leakage, damage, and restriction; determine needed action.	P-2	
20.02	Inspect hoses and connections (length, size, routing, bend radii, and protection); repair or replace as needed.	P-1	
20.03	Assemble hoses, tubes, connectors, and fittings in accordance with manufacturers’ specifications; use proper procedures to avoid contamination.P-2	P-2	
20.04	Inspect and replace fitting seals and sealants.	P-2	
21.0	Diagnose and repair hydraulic control valves--The student will be able to:		
21.01	Pressure test system safety relief valve; determine needed action.	P-2	
21.02	Perform control valve operating pressure and flow tests; determine needed action.	P-2	
21.03	Inspect, test, and adjust valve controls (electrical/electronic, mechanical, and pneumatic).	P-2	
21.04	Identify causes of control valve leakage problems (internal/external); determine needed action.	P-2	
21.05	Inspect pilot control valve linkages, cables, and PTO controls; adjust, repair, or replace as needed.	P-1	
22.0	Diagnose and repair hydraulic actuators--The student will be able to:		
	Comply with manufacturers’ and industry accepted safety practices associated with equipment lock out/tag out; pressure line
           release; implement/support (blocked or resting on ground); and articulated cylinder devices/machinery safety locks.	
22.01	Identify actuator type (single/double acting, multi-stage/telescopic, and motors).	P-1	
22.02	Identify the cause of seal failure; determine needed repairs.	P-2	
22.03	Identify the cause of incorrect actuator movement and leakage (internal and external); determine needed repairs.	P-2	
22.04	Inspect actuator mounting, frame components, and hardware for looseness, cracks, and damage; determine needed action.	P-2	
22.05	Remove, repair, and/or replace actuators in accordance with manufacturers’ recommended procedures.	P-2	
22.06	Inspect actuators for dents, cracks, damage, and leakage; determine needed action.	P-2	
22.07	Purge and/or bleed system in accordance with manufacturers’ recommended procedures.	P-1	

Additional Information

Laboratory Activities

Laboratory investigations that include scientific inquiry, research, measurement, problem solving, emerging technologies, tools and equipment, as well as, experimental, quality, and safety procedures are an integral part of this career and technical program/course. Laboratory investigations benefit all students by developing an understanding of the complexity and ambiguity of empirical work, as well as the skills required to manage, operate, calibrate and troubleshoot equipment/tools used to make observations. Students understand measurement error; and have the skills to aggregate, interpret, and present the resulting data. Equipment and supplies should be provided to enhance hands-on experiences for students.

Special Notes

The purpose of this program is to prepare students for employment as bus, truck and diesel engine mechanics, diesel mechanics helpers, mobile heavy equipment mechanics, construction equipment mechanics, industrial truck mechanics.

The safety guidelines in the student performance standards have been recommended in the ASE Program Certification Standards for Medium/Heavy Truck Technician Training Program administered by National Automotive Technicians Education Foundation (NATEF).

Career and Technical Student Organization (CTSO)

SkillsUSA is the intercurricular career and technical student organization(s) providing leadership training and reinforcing specific career and technical skills. Career and Technical Student Organizations provide activities for students as an integral part of the instruction offered. The activities of such organizations are defined as part of the curriculum in accordance with Rule 6A-6.065, F.A.C.

Cooperative Training – OJT

On-the-job training is appropriate but not required for this program.  Whenever offered, the rules, guidelines, and requirements specified in the OJT framework apply. 

Basic Skills

In PSAV programs offered for 450 hours or more, in accordance with Rule 6A-10.040, F.A.C., the minimum basic skills grade levels required for postsecondary adult career and technical students to complete this program are: Mathematics 9.0, Language 9.0, and Reading 9.0. These grade level numbers correspond to a grade equivalent score obtained on a state designated basic skills examination.  

Adult students with disabilities, as defined in Section 1004.02(7), Florida Statutes, may be exempted from meeting the Basic Skills requirements (Rule 6A-10.040). Students served in exceptional student education (except gifted) as defined in s. 1003.01(3)(a), F.S., may also be exempted from meeting the Basic Skills requirement. Each school district and Florida College must adopt a policy addressing procedures for exempting eligible students with disabilities from the Basic Skills requirement as permitted in Section 1004.91(3), F.S.

Students who possess a college degree at the Associate of Applied Science level or higher; who have completed or are exempt from the college entry-level examination; or who have passed a state, national, or industry licensure exam are exempt from meeting the Basic Skills requirement (Rule 6A-10.040, F.A.C.) Exemptions from state, national or industry licensure are limited to the certifications listed on the Basic Skills and Licensure Exemption List which may be accessed from the CTE Program Resources page.

Accommodations

Federal and state legislation requires the provision of accommodations for students with disabilities to meet individual needs and ensure equal access. Postsecondary students with disabilities must self-identify, present documentation, request accommodations if needed, and develop a plan with their counselor and/or instructors. Accommodations received in postsecondary education may differ from those received in secondary education. Accommodations change the way the student is instructed. Students with disabilities may need accommodations in such areas as instructional methods and materials, assignments and assessments, time demands and schedules, learning environment, assistive technology and special communication systems. Documentation of the accommodations requested and provided should be maintained in a confidential file.

Note: postsecondary curriculum and regulated secondary programs cannot be modified.

Additional Resources

For additional information regarding articulation agreements, Bright Futures Scholarships, Fine Arts/Practical Arts Credit and Equivalent Mathematics and Equally Rigorous Science Courses please refer to:

http://www.fldoe.org/academics/career-adult-edu/career-tech-edu/program-resources.stml