2015 - 2016
Florida Department of Education
Curriculum Framework 

Program Title:	Marine Service Technology 1
Program Type:	Career Preparatory
Career Cluster:	Transportation, Distribution and Logistics

NOTE: This program has been daggered for deletion with 2015-2016 being the last cohort of students permitted to enroll in the program. After 2015-2016, no new students may be enrolled in this program. Students already enrolled in the program may, at the District or Institution discretion, continue taking courses in the program until completion. The replacement enrollment option for students is the Marine Service Technologies (T400210) PSAV course.

PSAV – Career Preparatory	
Program Number	T500100	
CIP Number	0647061605	
Grade Level	30,31	
Standard Length	600 hours	
Teacher Certification	DIESEL MECH @7 7G 
GASENG RPR @7 7G	
CTSO	SkillsUSA	
SOC Codes (all applicable) 	49-3051 – Motorboat Mechanics and Service Technicians	
CTE Program Resources 	http://www.fldoe.org/academics/career-adult-edu/career-tech-edu/program-resources.stml	
Basic Skills Level	Mathematics:	9
Language:	9
Reading:	9	

Purpose

This program offers a sequence of courses that provides coherent and rigorous content aligned with challenging academic standards and relevant technical knowledge and skills needed to prepare for further education and careers in the Transportation, Distribution and Logistics career cluster; provides technical skill proficiency, and includes competency-based applied learning that contributes to the academic knowledge, higher-order reasoning and problem-solving skills, work attitudes, general employability skills, technical skills, and occupation-specific skills, and knowledge of all aspects of the Transportation, Distribution and Logistics career cluster. 

The content includes but is not limited to the following: service, repair and overhaul of four-stroke and two-stroke cycle engines and outboard motors; and service and repair of boating accessories.  With regard to the above, course content will include electrical systems, fuel systems, power transfer systems, ignition systems, cooling systems, lubrication systems, drive systems and boat and trailer rigging.

The course content should also include training in communication, leadership, human relations and employability skills; and safe, efficient work practices.

Additional Information relevant to this Career and Technical Education (CTE) program is provided at the end of this document.

Program Structure

This program is a planned sequence of instruction consisting of two occupational completion points.

This program is comprised of courses which have been assigned course numbers in the SCNS (Statewide Course Numbering System) in accordance with Section 1007.24 (1), F.S.  Career and Technical credit shall be awarded to the student on a transcript in accordance with Section 1001.44 (3) (b), F.S.

The following table illustrates the PSAV program structure:

OCP	Course Number	Course Title	Course Length	SOC Code	
A	MTE0003	Marine Rigger  	300 hours	49-3051	
B	MTE0050	Outboard Engine Technician 1 	300 hours	49-3051	

Common Career Technical Core – Career Ready Practices

Career Ready Practices describe the career-ready skills that educators should seek to develop in their students. These practices are not exclusive to a Career Pathway, program of study, discipline or level of education. Career Ready Practices should be taught and reinforced in all career exploration and preparation programs with increasingly higher levels of complexity and expectation as a student advances through a program of study. 

1. Act as a responsible and contributing citizen and employee. 

2. Apply appropriate academic and technical skills. 

3. Attend to personal health and financial well-being. 

4. Communicate clearly, effectively and with reason. 

5. Consider the environmental, social and economic impacts of decisions. 

6. Demonstrate creativity and innovation. 

7. Employ valid and reliable research strategies. 

8. Utilize critical thinking to make sense of problems and persevere in solving them. 

9. Model integrity, ethical leadership and effective management. 

10. Plan education and career path aligned to personal goals. 

11. Use technology to enhance productivity. 

12. Work productively in teams while using cultural/global competence. 

Standards

After successfully completing this program, the student will be able to perform the following:

01.0	Perform shop practices to industry standards.
02.0	Maintain and repair basic four-stroke cycle engines.
03.0	Maintain and repair basic two-stroke cycle engines.
04.0	Maintain and repair electrical systems.
05.0	Maintain and repair fuel systems.
06.0	Maintain and repair two-stroke cycle carburetors.
07.0	Use marine woods, metals and fiberglass.
08.0	Adjust and repair trailers.
09.0	Prepare and deliver sales merchandise.
10.0	Parts specialist and computer skills to industry standards.
11.0	Maintain and repair cooling systems.
12.0	Maintain and repair lubrication systems.
13.0	Perform gasket/seal operations and electronic test skills to industry standards.
14.0	Maintain and repair basic two stroke cycle outboard engines.
15.0	Maintain and repair outboard fuel systems.
16.0	Maintain and repair outboard cooling systems.
17.0	Maintain and repair outboard lubrication systems.
18.0	Maintain and repair outboard lower gear cases.

2015 - 2016
Florida Department of Education
Student Performance Standards

Program Title:	Marine Service Technology 
PSAV Number:	I490306
 
Course Number:  MTE0003
Occupational Completion Point:  A 
Marine Rigger – 300 Hours – SOC Code 49-3051 

Course Description:
Students will learn entry-level skills for the marine industry to be a marine technician.  Hands-on training combined with laboratory and classroom experiences gives the student a full understanding of 2 and 4 cycle internal combustion engines, high performance related equipment, and fuel systems.

CTE Standards and Benchmarks	
01.0	Perform shop practices to industry standards--The student will be able to:	
01.01	Comply with safety rules and regulations.	
01.02	Use hand tools safely and properly.	
01.03	Set up and use power tools safely and properly.	
01.04	Set up and use precision measuring tools.	
01.05	Drill and remove broken studs and install helicoils.	
01.06	Identify threaded fasteners by size, type, thread series, thread classes, material hardness and compatibility.	
01.07	Read, interpret and apply service manuals.	
01.08	Locate and match electrical units by their symbols on a wiring diagram.	
01.09	Demonstrate appropriate heating, cutting, and welding skills.	
02.0	Maintain and repair basic four-stroke cycle engines--The student will be able to:	
02.01	Explain the basic principles of the operation of four-stroke cycle internal combustion engines.	
02.02	Identify types of four-stroke cycle engines.	
02.03	Locate engine serial and model numbers.	
02.04	Identify engine assemblies and systems.	
03.0	Maintain and repair basic two-stroke cycle engines--The student will be able to:	
03.01	Explain the basic principles of the operation of two-stroke cycle internal combustion engines.	
03.02	Identify types of engines.	
03.03	Locate engine serial and model numbers.	
03.04	Identify engine assemblies and systems.	
04.0	Maintain and repair electrical systems--The student will be able to:	
04.01	Set up and use voltmeters, ammeters and ohmmeters.	
04.02	Locate and identify electrical circuit components.	
04.03	Sketch a typical circuit using a single wire system.	
04.04	Test storage batteries using a hydrometer.	
04.05	Test storage batteries using a light and load test.	
04.06	Charge storage batteries.	
04.07	Remove and replace batteries and service battery boxes.	
04.08	Repair damaged wire and electrical harnesses.	
04.09	Diagnose circuit troubles using continuity or a test light and low reading voltmeters to record voltage drop.	
04.10	Sketch and label typical fuel gage systems.	
04.11	Remove and replace ammeters or indicating lights.	
04.12	Remove and replace fuel gages.	
04.13	Remove and replace fuel-sending units.	
04.14	Diagnose gages and accessory system troubles using test lights, voltmeters, ammeters or detached sending units.	
04.15	Sketch typical circuits such as those for auto bilge pumps or navigation lights.	
04.16	Locate opens, shorts and grounds.	
04.17	Demonstrate proficiency in soldering/splicing skills.	
05.0	Maintain and repair fuel systems--The student will be able to:	
05.01	Identify and locate fuel system components (fuel tanks, lines, filters, etc.).	
05.02	Sketch and label the parts of total fuel systems.	
05.03	Service fuel lines and primer bulbs (vacuum test).	
05.04	Remove, clean, inspect and install fuel tanks.	
05.05	Identify basic carburetor circuits (chokes, floats, fuel inlets; idle, intermediate and high speeds; mains, etc.)	
05.06	Locate and identify fuel pumps and test the vacuum and pressure.	
05.07	Determine and make appropriate fuel oil mixtures.	
06.0	Maintain and repair two-stroke cycle carburetors--The student will be able to:	
06.01	Remove, clean, overhaul, replace and make final adjustments to carburetors.	
06.02	Diagnose exhaust problems such as back pressure and scavenging.	
07.0	Use marine woods, metals, and fiberglass--The student will be able to:	
07.01	Explain the hazards of a marine environment to woods, metals and fiberglass.	
07.02	Explain a galvanic series.	
07.03	Explain the theory for using given materials in boat repair activities.	
08.0	Adjust and repair trailers--The student will be able to:	
08.01	Make boat to trailer adjustments.	
08.02	Remove and replace lighting systems.	
08.03	Remove and replace wheel bearings and springs.	
08.04	Remove and replace brakes.	
08.05	Service and install trim and tilt systems.	
08.06	Remove and test cylinder rams.	
08.07	Adjust reverse locks.	
08.08	Adjust the trim and tilt.	
09.0	Prepare and deliver sales merchandise--The student will be able to:	
09.01	Make center line measurements for outboard motor installation.	
09.02	Center the plate height.	
09.03	Locate manufacturers' I.D. plates.	
09.04	Mount control boxes at the helm.	
09.05	Place wiring and cables in a neat and orderly manner.	
09.06	Adjust the control cables from the engine to the control box.	
09.07	Center the steering cable to the engine.	
09.08	Find suitable locations for accessories and mount them to the boat.	
09.09	Lubricate shafts, install propellers and fasten both securely.	
09.10	Check for proper levels.	
09.11	Check manufacturers' specifications.	
09.12	Test-run boats.	
09.13	Recheck work completed.	
09.14	Check manufacturers' installation procedures for stern drive units.	
09.15	Lubricate shafts and install propellers securely.	
09.16	Obtain maximum oil level capacity.	
09.17	Install or connect drain plugs, petcocks, hose clamps, hoses, etc.	
09.18	Find a suitable mount location and mount the engine securely in the boat.	
09.19	Set engines to manufacturers' specifications.	
09.20	Set, adjust and test engines to manufacturers' specifications.	
09.21	Remove and replace running lights.	
09.22	Troubleshoot lighting systems and accessories.	
09.23	Check and adjust throttles, cables, horns, lights and tachometers.	
10.0	Parts specialist and computer skills to industry standards--The student will be able to:	
10.01	Identify the skills needed to be a service writer.	
10.02	Identify the skills needed to be a parts specialist.	
10.03	Demonstrate appropriate computer skills.	
10.04	Identify gaskets and seals.	
10.05	Demonstrate knowledge of different parts and accessories.	
11.0	Maintain and repair cooling systems--The student will be able to:	
11.01	Explain the principles of cooling systems, including fresh water cooling systems.	
11.02	Trace water flow through cooling systems.	
12.0	Maintain and repair lubrication systems--The student will be able to:	
12.01	Identify the types and functions of lubrication systems.	
12.02	Explain the principles of lubrication systems.	
12.03	Identify and locate components of lubrication systems.	

2015 - 2016

Florida Department of Education
Student Performance Standards

Course Number:  MTE0050
Occupational Completion Point:  B 
Outboard Engine Technician 1 – 300 Hours – SOC Code 49-3051 

Course Description:
Students will learn entry-level skills for the marine industry to be a marine technician.  Hands-on training combined with laboratory and classroom experiences gives the student a full understanding of 2 and 4 cycle internal combustion engines’ cooling and lubrication systems.

CTE Standards and Benchmarks	
13.0	Perform gasket/seal operations and electronic test equipment skills to industry standards--The student will be able to:	
13.01	Identify and make gaskets and seals.	
13.02	Demonstrate appropriate skills in computerized test equipment.	
14.0	Maintain and repair basic two-stroke cycle outboard engines--The student will be able to:	
14.01	Disassemble engines.	
14.02	Remove, clean and inspect heads for cracks, warpage and damaged spark plug threads.	
14.03	Diagnose head problems by use of the visual inspection method.	
14.04	Diagnose head problems by use of the compression tester method.	
14.05	Diagnose head problems by use of cylinder air pressure method.	
14.06	Diagnose head problems by use of the stethoscope method.	
14.07	Remove, clean and inspect piston rods and assemblies.	
14.08	Measure out-of-round of pistons and cylinders.	
14.09	Hone cylinders.	
14.10	Check the total bearing surface of connecting rod bearings.	
14.11	Measure piston skirts and ring grooves.	
14.12	Measure the piston ring gap in cylinder bores.	
14.13	Install piston pins according to manufacturer's specifications.	
14.14	Check rod and piston assembly alignment.	
14.15	Install rings on pistons.	
14.16	Install piston rod assemblies.	
14.17	Measure and check crankshafts with a micrometer.	
14.18	Check needle bearings.	
14.19	Inspect crankshafts and install seal.	
14.20	Inspect, clean and/or replace reed valves.	
14.21	Reassemble engines.	
15.0	Maintain and repair outboard fuel systems--The student will be able to:	
15.01	Identify the major types of carburetors.	
15.02	Check and adjust throttle and governor linkages.	
15.03	Identify and service different types of EFI systems.	
15.04	Remove, service and replace air cleaners.	
15.05	Diagnose carburetor problems.	
16.0	Maintain and repair outboard cooling systems--The student will be able to:	
16.01	Disassemble, examine for problems and reassemble water pumps.	
16.02	Remove, check and replace thermostats.	
16.03	Use thermostat pressure relief systems.	
16.04	Service manifolds and thermostat housings.	
17.0	Maintain and repair outboard lubrication systems--The student will be able to:	
17.01	Check engines for oil leaks.	
17.02	Change engine oil and filters.	
17.03	Check engine oil pressure and level.	
17.04	Recognize and use only recommended oil.	
17.05	Inspect and service oil-metering systems.	
18.0	Maintain and repair outboard lower gear cases--The student will be able to:	
18.01	Remove and replace lower gear cases.	
18.02	Reshim lower gear cases.	
18.03	Refill lower gear cases with specified oil.	
18.04	Determine propeller pitch diameter and hub type.	

Additional Information

Laboratory Activities

Laboratory investigations that include scientific inquiry, research, measurement, problem solving, emerging technologies, tools and equipment, as well as, experimental, quality, and safety procedures are an integral part of this career and technical program/course. Laboratory investigations benefit all students by developing an understanding of the complexity and ambiguity of empirical work, as well as the skills required to manage, operate, calibrate and troubleshoot equipment/tools used to make observations. Students understand measurement error; and have the skills to aggregate, interpret, and present the resulting data. Equipment and supplies should be provided to enhance hands-on experiences for students. 

Special Notes

The purpose of this program is to prepare students for employment as machinery mechanics; marine engines, or outboard motor mechanics.

This program focuses on broad, transferable skills and stresses understanding and demonstration of the following elements of the Marine Service industry; planning, management, finance, technical and product skills, underlying principles of technology, labor issues, community issues and health, safety, and environmental issues.

Career and Technical Student Organization (CTSO)

SkillsUSA is the intercurricular career and technical student organization(s) providing leadership training and reinforcing specific career and technical skills. Career and Technical Student Organizations provide activities for students as an integral part of the instruction offered. The activities of such organizations are defined as part of the curriculum in accordance with Rule 6A-6.065, F.A.C.

Cooperative Training – OJT

On-the-job training is appropriate but not required for this program.  Whenever offered, the rules, guidelines, and requirements specified in the OJT framework apply. 

Basic Skills

In PSAV programs offered for 450 hours or more, in accordance with Rule 6A-10.040, F.A.C., the minimum basic skills grade levels required for postsecondary adult career and technical students to complete this program are: Mathematics 9.0, Language 9.0, and Reading 9.0. These grade level numbers correspond to a grade equivalent score obtained on a state designated basic skills examination.  

Adult students with disabilities, as defined in Section 1004.02(7), Florida Statutes, may be exempted from meeting the Basic Skills requirements (Rule 6A-10.040). Students served in exceptional student education (except gifted) as defined in s. 1003.01(3)(a), F.S., may also be exempted from meeting the Basic Skills requirement. Each school district and Florida College must adopt a policy addressing procedures for exempting eligible students with disabilities from the Basic Skills requirement as permitted in Section 1004.91(3), F.S.

Students who possess a college degree at the Associate of Applied Science level or higher; who have completed or are exempt from the college entry-level examination; or who have passed a state, national, or industry licensure exam are exempt from meeting the Basic Skills requirement (Rule 6A-10.040, F.A.C.) Exemptions from state, national or industry licensure are limited to the certifications listed on the Basic Skills and Licensure Exemption List which may be accessed from the CTE Program Resources page.

Accommodations

Federal and state legislation requires the provision of accommodations for students with disabilities to meet individual needs and ensure equal access. Postsecondary students with disabilities must self-identify, present documentation, request accommodations if needed, and develop a plan with their counselor and/or instructors. Accommodations received in postsecondary education may differ from those received in secondary education. Accommodations change the way the student is instructed. Students with disabilities may need accommodations in such areas as instructional methods and materials, assignments and assessments, time demands and schedules, learning environment, assistive technology and special communication systems. Documentation of the accommodations requested and provided should be maintained in a confidential file.

Note: postsecondary curriculum and regulated secondary programs cannot be modified.

Additional Resources

For additional information regarding articulation agreements, Bright Futures Scholarships, Fine Arts/Practical Arts Credit and Equivalent Mathematics and Equally Rigorous Science Courses please refer to:

http://www.fldoe.org/academics/career-adult-edu/career-tech-edu/program-resources.stml